QIDI PETG-Tough Green Filament Review (2026): A Spec-Based Look
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
QIDI's PETG-Tough is a 1kg spool of 1.75mm filament, not a printer: a PETG modified for toughness, which QIDI says reaches more than three times the notch impact strength of ordinary PETG. It also flows more easily, so QIDI rates it up to 400mm/s and pairs it with its X-Max3. Settings on the page are 240-280°C nozzle, 70-80°C bed, 100% fan and 40-400mm/s, with ±0.02mm tolerance. This review covers the green spool, which showed low stock; we worked from QIDI's listing, not test prints.
What stands out
- Notch impact over 3x ordinary PETG, per QIDI
- High flow for speeds up to 400mm/s
- Nozzle, bed, fan and speed all listed
- ±0.02mm tolerance, foil vacuum pack
Who it fits
Good fit for
People printing functional parts that take knocks, such as tool holders, jigs and clips, on a fast printer that can push PETG at speed.
Who should skip it
Skip it if you need a heat or UV figure: QIDI calls it heat and weather resistant but gives no number. Also note the low stock at our check, and the red version is sold as a separate listing.
Verdict: A toughened, fast-flowing PETG with clear settings.
PETG-Tough figures in context
Notch impact 3x+ ordinary PETG
QIDI's main claim; it gives a ratio, not a J/m value, so compare it only with plain PETG.
40-400mm/s
Lower extrusion pressure lets it keep up on fast machines; slow printers can run it too.
240-280°C nozzle, 70-80°C bed, 100% fan
Hotter than many PETGs at the top of the range, so check your hotend's limit.
1.75mm ±0.02mm, 1kg
Tight tolerance on a standard spool.
Material and packaging
PETG-Tough is pitched as rigid yet tough, odorless while printing, and resistant to impact and heat, with low shrinkage and a smooth surface that QIDI says post-processes easily. The spool comes vacuum sealed in aluminum foil. QIDI asks you to clip the loose end through the spool's fixed hole after each use to avoid tangles.
Running it day to day
Start near the middle of QIDI's range, around 260°C with a 75°C bed and full part cooling, then raise speed as far as your printer allows. QIDI recommends its X-Max3 but lists the spool as compatible with most 1.75mm FDM printers.
Before buying the green PETG-Tough spool
Worth checking.
Check before you buy
- Your hotend reaches 260-280°C comfortably
- Your parts need impact strength more than heat figures
- Green is the color you want (red is a separate listing)
- Low stock may delay shipping
The product at a glance
QIDI Tech PETG-Tough 1.75mm Filament
Best for: Impact-resistant parts
- Material Type
- PETG
- Filament Diameter
- 1.75mm
- Net Weight
- 1kg
- Max Print Speed
- 400mm/s
- Dimensional Accuracy
- +/- 0.02mm
- Color
- Green
View on Amazon: QIDI Tech PETG-Tough 1.75mm Filament Affiliate link
QIDI PETG-Tough green 1kg: impact-modified PETG with over 3x the notch impact of plain PETG, 40-400mm/s, 240-280°C, 70-80°C bed, ±0.02mm; low stock at our check.
Pros
- Toughened formula
- Fast-print rating
- Settings and tolerance listed
Cons
- No heat or UV figures
- Runs up to 280°C
- Low stock
Good fit if
- You print green clips or jigs that get dropped and flexed
Skip if
- You need a stated heat deflection temperature
Verdict: QIDI's tough PETG for functional prints.
Specifications side by side
| Spec | QIDI Tech PETG-Tough 1.75mm Filament |
|---|---|
| Material Type | PETG |
| Filament Diameter | 1.75mm |
| Net Weight | 1kg |
| Max Print Speed | 400mm/s |
| Dimensional Accuracy | +/- 0.02mm |
| Compatible Material | PETG |
| Color | Green |
| Size | 1.75Mm |
| Surface Finish | Smooth |
| Resin Type | Tough |
Frequently asked questions
Is QIDI PETG-Tough a 3D printer?
No, it is a 1kg spool of 1.75mm PETG filament; the old title was wrong.
What settings does QIDI list for green PETG-Tough?
240-280°C nozzle, 70-80°C bed, 100% fan and 40-400mm/s.
How much tougher is PETG-Tough than normal PETG?
QIDI says its notch impact strength is more than three times that of ordinary PETG.
Can PETG-Tough print at high speed?
Yes, QIDI rates it up to 400mm/s thanks to high fluidity and lower extrusion pressure.
Which QIDI printer is PETG-Tough made for?
QIDI recommends the X-Max3 but says it works with most 1.75mm FDM printers.
Featured in
See also
- qidi pa12 cf carbon fiber nylon filament review
- bambu lab petg hf green filament review
- bambu lab abs white filament refill review
- r qidi technology pla rapido filament 1 75mm review
- r qidi technology abs rapido filament review
- QIDI ASA Filament Review: Who It Fits and Who Should Skip It
- QIDI PETG-Tough Filament (Red, 1.75mm, 1kg) Review
- best R QIDI Technology 3d printers
- easycargo 30pcs 3d printer heatsink review
