Semdon Tri-Color Silk PLA Filament (Red/Blue/Green, 1kg) Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Semdon's tri-color silk PLA runs red, blue and green side by side in every inch of the strand, so a print shows all three colors at once rather than cycling through them along the spool. That is the key difference from length-wise rainbow filament: even a small keychain or ornament gets the full effect, and the color you see shifts as the model turns. Semdon says each print looks different depending on its shape. The 1kg spool is glossy silk PLA with a low-temperature window of 200-230°C, a 50-300mm/s speed range and 0.02mm accuracy, and Semdon says it works with ordinary PLA profiles on printers like the Ender 3 and Prusa models. It also claims better bend resistance than other PLA. The listing title names no brand; the bullets call it SEMDON. Semdon's 80% clog reduction claim has no stated baseline. We assembled this from the listing and its spec fields rather than a test print.
What stands out
- Coextruded silk PLA, red/blue/green
- 1kg spool
- 200-230°C, 50-300mm/s
- 0.02mm accuracy
- Pre-dried, vacuum sealed
Who it fits
Good fit for
Makers of vases, ornaments, cosplay pieces and gifts who want a three-color shimmer without painting or a multi-color system.
Who should skip it
Anyone who wants clean single-color areas or a controlled color change at a set height.
Verdict: A glossy red-blue-green coextruded silk PLA that suits small decorative prints with a shifting look.
Semdon tri-color silk PLA specs
Red, blue, green coextruded
All three colors in every inch of filament.
200-230°C
Low-temperature silk formula.
50-300mm/s
Wide speed range, per Semdon.
0.02mm accuracy
Smooth feeding.
Silk gloss
Shiny surface that shifts with the angle.
How coextruded tri-color prints
Because the three colors run side by side, which color faces you depends on the direction each wall is printed. Round vases and twisted shapes show bands of red, blue and green sweeping around the part; flat-faced models may show mostly one or two colors on a given side. Semdon pitches it for cosplay props and Christmas decor.
Printing Semdon red-blue-green silk
Use your normal PLA profile within 200-230°C, as Semdon suggests. Silk PLA shines most at moderate speeds and with a single, smooth outer wall, so vase mode suits it well. Try a slight temperature change if the gloss looks dull; silk finish depends on how the outer wall cools.
Before buying Semdon tri-color silk
Checks.
Check before you buy
- You want red, blue and green in one Semdon print
- Your prints are decorative, not engineering parts
- You accept angle-dependent color on Semdon silk
- Your printer runs PLA at 200-230°C
The product at a glance
Semdon Tri-Color Gradient Silk PLA 1.75mm
Best for: Shimmering small decor
- Material Type
- PLA
- Filament Diameter
- 1.75mm
- Net Weight
- 1KG
- Max Print Speed
- 300mm/s
- Dimensional Accuracy
- 0.02mm
- Surface Finish
- Silk
View on Amazon: Semdon Tri-Color Gradient Silk PLA 1.75mm Affiliate link
Semdon tri-color silk PLA 1kg: red, blue and green coextruded in every inch, glossy, 200-230°C, 50-300mm/s, 0.02mm accuracy.
Pros
- All three colors even on small prints
- Works with PLA profiles
- Glossy silk finish
Cons
- Color depends on viewing angle
- No brand in the listing title
- Silk PLA is not for load parts
Good fit if
- You print red-blue-green silk vases or ornaments
Skip if
- You need a controlled color change by layer
Verdict: A three-color silk PLA for small decorative prints.
Specifications side by side
| Spec | Semdon Tri-Color Gradient Silk PLA 1.75mm |
|---|---|
| Material Type | PLA |
| Filament Diameter | 1.75mm |
| Net Weight | 1KG |
| Max Print Speed | 300mm/s |
| Dimensional Accuracy | 0.02mm |
| Surface Finish | Silk |
| Printing Technology | FDM |
| Color Printing | Multi-Color |
| Compatible Material | PLA |
| Size | 1KG |
| Finish | Silk |
| Weight | 2.2 pounds |
| Color | 1kg Pla Red-blue-green |
| Model | 1 |
Frequently asked questions
How does Semdon tri-color silk PLA differ from rainbow filament?
Every inch contains red, blue and green side by side, so small prints show all three colors instead of one color at a time.
What temperature does Semdon red-blue-green silk need?
200-230°C, with a 50-300mm/s speed range.
Does Semdon tri-color PLA need special settings?
Semdon says standard PLA profiles work on printers like the Ender 3 and Prusa models.
Is Semdon tri-color silk PLA strong?
Semdon claims it bends repeatedly with less breakage than other PLA, but silk PLA is chosen for looks rather than strength.
What accuracy does the Semdon tri-color spool give?
0.02mm.
