Aorita3D 290x210mm NFEP Film 5-Pack Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Aorita3D's 290x210mm NFEP film 5-pack is a set of A4-size release sheets for 9.1-10.1 inch resin printers, and its best argument is coverage: five 0.15mm sheets cut to fit a long list of vats, named on the page as ELEGOO Saturn S and Saturn 2, Anycubic Photon Mono X 6K, M3 Plus, Phrozen Sonic Mighty 4K, and E10/X10 class machines. Aorita3D quotes 95% light transmission, lower release force than plain film, resistance to resin, heat tolerance up to 250°C and a protective layer on both sides that peels off before fitting. One thing to know up front: the listing calls the material NFEP in the bullets, adds "pfa" in the title and "FEP 2.0" in one bullet, so treat it as an NFEP-type film and do not expect PFA figures. The 90% success rate it quotes is a seller claim, not a measured result we can confirm. We went through Aorita3D's page and specs only.
What stands out
- Five 290x210x0.15mm sheets
- 95% light transmission claimed
- Protective film on both sides
- Fits many 9.1-10.1 inch vats
Who it fits
Good fit for
Owners of a Saturn S, Saturn 2, Photon Mono X 6K or similar 9-10 inch resin printer who replace film often and want five sheets on hand.
Who should skip it
Owners of 7-inch or smaller vats, Saturn 3/4 class printers with different frames, or anyone who needs a specific PFA or ACF film.
Verdict: A good-value stack of A4 release sheets for 9-10 inch vats, as long as the size matches your frame.
Aorita3D A4 NFEP film specs
290 x 210 x 0.15mm
A4 sheet you clamp in the vat frame and trim to fit.
5 sheets
Enough to replace film several times or keep spares for a second vat.
95% light transmission
The listed figure for UV passing through the film.
Up to 250°C
Heat tolerance claimed by the seller.
Dual-side protective film
Peel both sides off before fitting the sheet.
NFEP versus plain FEP
NFEP films are designed to let prints peel off the vat floor with less force than standard FEP, which helps thin supports and large flat layers. Aorita3D adds resin corrosion resistance and reusability to its pitch. The listing mixes three names (NFEP, pfa, FEP 2.0) for one product, so judge it by the size and the 95% figure rather than the label.
Fitting an Aorita3D A4 sheet
Drain and clean the vat, remove the old film, then peel the protective layers off a new sheet and clamp it evenly in the frame. Tension it until it sounds like a drum, trim the excess, and run an exposure test before a real print, because a new film can change release behavior. Keep the other four sheets flat and covered.
Before buying the Aorita3D 290x210 NFEP pack
Checks.
Check before you buy
- Your vat takes an A4 or 290x210mm sheet for Aorita3D NFEP
- Your printer is on the Aorita3D list (Saturn S, Saturn 2, Mono X 6K, M3 Plus, Mighty 4K)
- You have the tools to tension and trim film in the vat
The product at a glance
Aorita3D 290x210mm NFEP Film 5-Pack
Best for: 9-10 inch resin vats
- Dimensions
- 290x210x0.15mm
- Maximum Temperature
- 250°C
- Release Film Type
- NFEP
- Film Thickness
- 0.15mm
- Printing Technology
- Resin
- Resolution
- 4K
View on Amazon: Aorita3D 290x210mm NFEP Film 5-Pack Affiliate link
Aorita3D A4 NFEP film, five 290x210x0.15mm sheets for 9.1-10.1 inch resin vats; 95% light transmission and dual-side protection film claimed.
Pros
- Five sheets per pack
- Long printer list on the page
- Protective layers on both faces
Cons
- Material named three ways on the listing
- Success-rate figure is a seller claim
- Not for small 6-7 inch vats
Good fit if
- You own a Saturn 2 or Photon Mono X 6K and replace film often
Skip if
- Your vat is not a 290x210mm A4 frame
Verdict: Plenty of A4 film for 9-10 inch vats.
Specifications side by side
| Spec | Aorita3D 290x210mm NFEP Film 5-Pack |
|---|---|
| Dimensions | 290x210x0.15mm |
| Maximum Temperature | 250°C |
| Release Film Type | NFEP |
| Film Thickness | 0.15mm |
| Printing Technology | Resin |
| Resolution | 4K |
| Size | 290*210*0.15mm |
Frequently asked questions
What size is the Aorita3D NFEP 5-pack?
Each sheet is 290 x 210 x 0.15mm, A4 size, and there are five of them.
Which printers does the Aorita3D 290x210 film fit?
The listing names ELEGOO Saturn S and Saturn 2, Photon Mono X 6K, M3 Plus, Sonic Mighty 4K, and E10/X10 9.1-10.1 inch printers.
Is the Aorita3D 290x210 film NFEP or PFA?
The bullets call it NFEP, the title also says pfa and one bullet says FEP 2.0; treat it as an NFEP-type release film.
What light transmission does Aorita3D list for this film?
95%.
Featured in
See also
- eiijugaloo saturn 4 ultra silver dust cover review
- greensen k2 plus xy axis timing belt review
- nova3d water washable tough resin white 1kg review
- aorita3d nfep release film 280x200 review
- aorita3d acf release film 280x200 review
- AORITA3D 450x300mm ACF Release Film V3.0 Review (2026)
- easycargo 100pcs 12 sizes 15mm review
- yamaha stage custom birch 5pc review
