As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

AORITA3D 280×200mm NFEP Release Film 5-Pack Review: Who It Fits and Who Should Skip It

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

Release film is the clear sheet at the bottom of a resin vat, and it wears, clouds or punctures over time. This AORITA3D pack gives five 280×200mm NFEP sheets, 0.15mm thick, for under $35, aimed at mid-size printers: the Elegoo Saturn series, Creality Halot-Sky, Halot-LITE and Halot-Ray, NOVA Whale2, G6 and GKtwo. The title calls it both PFA and NFEP film. AORITA3D pitches it as an upgrade over plain FEP, with lower peel force, longer life and high UV transmittance that it says can speed prints, though no percentage is given. Only a few packs showed as available when we looked, and every point above comes from the listing.

What stands out

  • Five sheets per pack
  • 280×200×0.15mm
  • Lower peel force than FEP, per AORITA3D
  • Fits Saturn and Halot vats

Who it fits

Good fit for

Owners of 8.9 to 10-inch class resin printers who replace vat film regularly and want several spares from one order.

Who should skip it

Those chasing faster lifts on a printer that supports ACF film may prefer AORITA3D's 0.3mm ACF instead. Owners of small 6-inch or huge 12-inch-plus printers need a different size.

Verdict: A cost-effective stack of NFEP sheets for mid-size vats, with vague performance claims.

NFEP film sizing

280×200mm sheets

Cut-to-fit for Saturn and Halot-class vats; check your frame.

0.15mm thickness

Thinner than ACF, typical for FEP-style films.

5 pieces

Several vat rebuilds from one purchase.

NFEP vs FEP

AORITA3D claims easier peeling and longer service life.

Listing inconsistencies

The title names both "pfa Film" and "Nfep Film"; nFEP films are commonly PFA-based, so this is likely the same material described two ways. "Saturn Series" is broad: Saturn 3 and 4 vats differ from the original Saturn, so measure your frame before ordering. The UV transmittance claim has no number.

Changing a vat film

Drain and clean the vat, unscrew the frame, lay a new sheet flat, and tension it evenly before trimming. A tight film sounds like a drum when tapped. Run a short exposure test after each change, since peel behavior can shift.

Before buying this NFEP pack

Verify these.

Check before you buy

  • Your vat accepts 280×200mm film
  • Your printer is on the listed models
  • You have the tools to re-tension a vat
  • You do not need ACF

The product at a glance

AORITA3D PFA Film 280x200mm

Best for: Mid-size resin vat maintenance

Dimensions
280*200*0.15mm
Release Film Type
PFA
Film Thickness
0.15mm

View on Amazon: AORITA3D PFA Film 280x200mm Affiliate link

AORITA3D NFEP film: five 280×200×0.15mm release sheets for Saturn, Halot-Sky/LITE/Ray, NOVA Whale2, G6 and GKtwo resin vats.

Pros

  • Five spares per pack
  • Claims easier peel than FEP
  • Fits many mid-size printers

Cons

  • PFA/NFEP naming mixed
  • No transmittance number
  • Low stock at last check

Good fit if

  • You run a Saturn or Halot-Sky
  • You change vat film often

Skip if

  • Your printer supports ACF and you want it
  • Your vat is a different size

Verdict: Good-value mid-size NFEP spares.

Specifications side by side

Spec AORITA3D PFA Film 280x200mm
Dimensions 280*200*0.15mm
Release Film Type PFA
Film Thickness 0.15mm
Size NFEP 280*200

Frequently asked questions

Which printers does this AORITA3D NFEP pack fit?

Elegoo Saturn series, Creality Halot-Sky, Halot-LITE, Halot-Ray, NOVA Whale2, G6 and GKtwo, per the listing.

How thick is AORITA3D's 280×200 NFEP film?

0.15mm.

Is AORITA3D NFEP the same as PFA film?

The title uses both terms; the bullets call it NFEP.

How many AORITA3D NFEP sheets come in one order?

Five.

See also