Greensen K2 Plus X/Y Axis Timing Belt Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Greensen's replacement timing belt is an open rubber belt for the X and Y axes of the Creality K2 Plus, and it is worth a look mainly as a low-cost spare: roughly 8mm wide and 75.5 inches long, cut to length by you and fitted during maintenance. That width matters, because the K2 Plus does not use the 6mm belts sold for most Ender-class printers, and Greensen names the K2 Plus directly. The listing stays thin on the details belt buyers usually compare: it gives no tooth pitch (GT2 or otherwise), no glass or steel core and no tooth count, and its model field is a random code. Greensen describes it as rubber, wear resistant and quiet, which reads as marketing rather than measured data. If your K2 Plus belt has frayed or stretched, this may cover one axis or more depending on how much your machine needs, so measure the old belts first. We used Greensen's listing alone for this review.
What stands out
- Made for K2 Plus X/Y axes
- About 8mm wide
- About 75.5in long, open ended
- Rubber construction
Who it fits
Good fit for
K2 Plus owners who want an inexpensive 8mm belt on hand for X/Y maintenance and are happy to measure and cut it themselves.
Who should skip it
Anyone who needs a confirmed GT2 pitch, a reinforced core, or a 6mm belt for an Ender-style printer.
Verdict: A cheap open belt sized for the K2 Plus; the missing pitch and core data mean you should compare it with your old belt before cutting.
Greensen K2 Plus belt specs
8mm width (approx.)
Matches the wider belts on the K2 Plus, not the 6mm common on smaller printers.
75.5in length (approx.)
About 1.9m of open belt to cut to the run you need.
Open belt
Ends are free, so you clamp them at the carriage like the original.
Rubber
The only material stated; no glass or steel core is listed.
Tooth pitch
Not given on the listing.
What is missing from the Greensen listing
Belts for CoreXY printers like the K2 Plus are usually judged on pitch, core and stretch. Greensen states only width, length and rubber, and says buyers should match the model type before use. Lay the new belt teeth to teeth against your old one to confirm the pitch, and check that the total length covers the axis you are replacing.
Fitting the Greensen belt on a K2 Plus
Note the routing of the old belt first, or photograph it. Remove it, cut the new belt to the same length plus a little margin, thread it through the pulleys and clamp both ends, then set tension per Creality's procedure for the K2 Plus. On a CoreXY machine both X/Y belts should end up at matched tension, so replacing them together is often simpler.
Before buying the Greensen K2 Plus belt
Checks.
Check before you buy
- Your printer is a K2 Plus with 8mm X/Y belts for the Greensen belt
- 75.5 inches of Greensen belt covers the axes you are replacing
- You can confirm the tooth pitch against your old K2 Plus belt
The product at a glance
Greensen 8mm Rubber Timing Belt for K2 Plus
Best for: K2 Plus X/Y belt spare
- Primary Material
- Rubber
View on Amazon: Greensen 8mm Rubber Timing Belt for K2 Plus Affiliate link
Greensen open timing belt for K2 Plus X/Y, about 8mm by 75.5in, rubber; no pitch or core listed.
Pros
- Named fit for the K2 Plus
- 8mm width matches the printer
- Low-cost spare
Cons
- No tooth pitch stated
- No core material listed
- Random model code
Good fit if
- You keep spare belts for a K2 Plus
Skip if
- You need a documented GT2 belt with a glass core instead of the Greensen
Verdict: A basic 8mm spare belt for the K2 Plus.
Specifications side by side
| Spec | Greensen 8mm Rubber Timing Belt for K2 Plus |
|---|---|
| Primary Material | Rubber |
| Model | Greensenv8xni1cu9h |
Frequently asked questions
What size is the Greensen K2 Plus belt?
About 8mm wide and 75.5 inches long, open ended.
Is the Greensen belt GT2?
The listing does not give a tooth pitch, so compare it with your old belt.
Which printer is the Greensen timing belt for?
The Creality K2 Plus, X and Y axes.
What is the Greensen K2 Plus belt made of?
Rubber; no reinforcing core is listed.
See also
- nova3d water washable tough resin white 1kg review
- anycubic photon mono 4 ultra review
- anycubic kobra s1 max printer only review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- ideaformer 3d conveyor belt 3d printer review
- unxuey 50pcs 3d printer heatsink review
