As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

NOVA3D Water Washable Tough Resin (White, 1kg) Review (2026)

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

NOVA3D's white water washable tough resin comes in a 1kg bottle for 405nm LCD, DLP and SLA printers, and its pitch is easy to state: a tough resin you rinse in water instead of IPA, in a white that suits parts you plan to prime and paint. The white listing aims it at mecha models, saying parts stay intact even when screws are tightened into them and that it resists bending, compression and impact. It also promises low odor, low viscosity, low shrinkage and a matte surface that looks less like plastic. What the page does not give is any exposure time, bottom layer setting, hardness or elongation figure, so you start from your printer's water-washable profile and tune from a test print. The bullets are a bit careless: one heading calls it grey resin and another says 1000ml while the title says 1kg. This is the white bottle of the same tough water-wash line NOVA3D also sells in grey. We worked from NOVA3D's listing only.

What stands out

  • Water washable, no IPA
  • Tough enough for screws in mecha parts
  • Matte white finish
  • 405nm, LCD/DLP/SLA

Who it fits

Good fit for

Resin printer owners who build mecha kits, snap-fit or screwed parts and want water cleanup and a white base for paint.

Who should skip it

Anyone who needs published exposure settings or mechanical data, or who prints clear or dark display pieces.

Verdict: A white tough resin with easy water cleanup; budget a test print to dial in exposure.

NOVA3D white tough resin specs

1kg bottle

The title says 1kg; one bullet says 1000ml.

405nm UV

Matches standard LCD, DLP and SLA resin printers.

Water washable

Rinse in water rather than alcohol.

Model 2002-015-0001-3

NOVA3D's code for the white bottle.

Exposure settings

Not listed; start from a water-washable profile.

What white tough resin is for

A tough resin bends a little before it breaks, which helps with thin parts, pegs and joints that take a screw, the use NOVA3D highlights for mecha builds. White shows surface detail clearly and takes primer and paint without a dark base showing through. The matte finish also hides layer sheen better than glossy standard resins, per the listing.

Printing and cleaning NOVA3D white

Shake the bottle well, print a calibration model to find the exposure, and keep supports a little heavier than usual since tough resins can flex during peel. Rinse parts in water, let them dry fully, then post-cure. Water-wash resin still goes into the wash water, so let it cure in sunlight before disposal rather than pouring it down the drain.

Before buying NOVA3D white tough resin

Checks.

Check before you buy

  • Your printer uses 405nm light for NOVA3D white resin
  • You can run an exposure test with NOVA3D white first
  • You want white for priming and painting NOVA3D parts

The product at a glance

NOVA3D 1kg Water-Washable Tough Resin

Best for: Mecha and paintable tough parts

Resin Type
Water-Washable, Tough
Curing Wavelength
405nm
Compatible Technology
LCD, DLP, SLA
Net Weight
1kg
Cleaning Method
Water
Printing Technology
Resin

View on Amazon: NOVA3D 1kg Water-Washable Tough Resin Affiliate link

NOVA3D white tough water-wash resin, 1kg, 405nm: water cleanup, matte finish, pitched at mecha parts that take screws; no exposure data listed.

Pros

  • No IPA needed
  • Tough enough for screwed parts
  • White base for paint

Cons

  • No exposure or mechanical data
  • Bullets say grey and 1000ml
  • Wash water still needs curing

Good fit if

  • You print mecha kits or snap-fit parts to paint

Skip if

  • You need a datasheet with NOVA3D white exposure times

Verdict: A white tough resin with simple water cleanup.

Specifications side by side

Spec NOVA3D 1kg Water-Washable Tough Resin
Resin Type Water-Washable, Tough
Curing Wavelength 405nm
Compatible Technology LCD, DLP, SLA
Net Weight 1kg
Cleaning Method Water
Printing Technology Resin
Features Low Odor, Fast Curing
Size 1KG
Resolution 12K, 14K
Color White1kg
Model 2002-015-0001-3

Frequently asked questions

Is NOVA3D white tough resin water washable?

Yes, NOVA3D says it rinses in water and does not need IPA.

What printers work with NOVA3D white tough resin?

405nm LCD, DLP and SLA printers, including 12K and 14K LCD models.

What exposure does NOVA3D list for the white resin?

None; the listing does not give exposure or layer settings.

What is NOVA3D white tough resin good for?

NOVA3D aims it at tough parts such as mecha models that must hold screws without cracking.

See also