AORITA3D 450x300mm ACF Release Film V3.0 Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
AORITA3D sells this ACF film V3.0 as one sheet of 450x300mm at 0.3mm thick, sized for large-format resin printers. The listing names the ELEGOO Jupiter and Jupiter SE, Creality Halot-Max, ANYCUBIC Photon M3 Max and Phrozen Sonic Mega. On a vat that size, film is the most expensive consumable after resin, so a single sheet makes sense for someone who has just torn a film and needs one replacement now rather than a stock. AORITA3D's claims are relative to nFEP: lower release force, quieter peeling, longer life, and higher heat resistance, with a working rating of 260°C and a 305°C melting point. The inch figure on the page (0.01in thick) does not match 0.3mm, so trust the metric size. AORITA3D does not give transmittance, cut-hole positions or install steps, and the large vats differ in frame layout, so measure yours. The points here are taken from AORITA3D's listing and published specs; we did not install the film.
What stands out
- One 450x300mm ACF sheet, 0.3mm
- Names Jupiter, Halot-Max, M3 Max, Sonic Mega
- Lower peel force than nFEP claimed
- Rated 260°C working, 305°C melt
- No transmittance figure listed
Who it fits
Good fit for
Owners of one large resin printer such as a Jupiter or Sonic Mega who need a single replacement film without paying for a multi-pack.
Who should skip it
Owners of 6- to 10-inch printers (wrong size), and print farms that re-film often and would do better with a pack of several sheets.
Verdict: A one-off ACF replacement for big-format vats, with fit to be measured.
AORITA3D 450x300 ACF specs
450x300mm
Large-format vat size; trim to your frame if needed.
0.3mm thick
Typical ACF gauge, stiffer than 0.15mm FEP.
V3.0
AORITA3D's current ACF version per the title.
260°C working rating
Heat resistance well above vat temperatures.
1 sheet
A single replacement, not a stock.
ACF versus nFEP on a large vat
On a wide vat the suction between a big cured layer and the film is high, which is where ACF's lower release force helps most: less pull on supports and less noise at each lift. AORITA3D also claims a longer life than nFEP. The listing does not give a transmittance figure, so exposure times may need a check after fitting.
Fitting the AORITA3D 450x300 sheet
Remove the vat's frame, transfer the hole pattern from the old film onto the new sheet, and tighten the frame evenly so the film is flat. Leak-test with a paper towel before pouring resin, then run an exposure test, since the old film's settings may not carry over.
Before buying the AORITA3D 450x300 ACF
Checks.
Check before you buy
- Your resin vat takes a 450x300mm film
- Your printer is a Jupiter, Halot-Max, Photon M3 Max or Sonic Mega
- One AORITA3D ACF sheet is enough for now
The product at a glance
Aorita3D 450x300 ACF Release Film
Best for: Large-format vat repair
- Dimensions
- 450*300*0.3mm
- Maximum Temperature
- 260 °C
- Release Film Type
- ACF
- Film Thickness
- 0.3mm
View on Amazon: Aorita3D 450x300 ACF Release Film Affiliate link
One AORITA3D 450x300x0.3mm ACF V3.0 sheet for Jupiter, Halot-Max, Photon M3 Max and Sonic Mega vats, with lower peel force than nFEP claimed.
Pros
- Lists four big-format printers
- Lower release force than nFEP
- Single-sheet buy
Cons
- No transmittance figure
- Inch thickness does not match mm
- No hole pattern or install steps
Good fit if
- You need one film for a Jupiter or Sonic Mega
Skip if
- You re-film several large vats
Verdict: A single large ACF replacement sheet.
Specifications side by side
| Spec | Aorita3D 450x300 ACF Release Film |
|---|---|
| Dimensions | 450*300*0.3mm |
| Maximum Temperature | 260 °C |
| Release Film Type | ACF |
| Film Thickness | 0.3mm |
| Size | ACF 450*300 |
| Model | ACF450_1 |
Frequently asked questions
Which printers does the AORITA3D 450x300 ACF fit?
ELEGOO Jupiter/Jupiter SE, Creality Halot-Max, ANYCUBIC Photon M3 Max and Phrozen Sonic Mega.
How thick is AORITA3D's 450x300 ACF film?
0.3mm.
What temperature can the AORITA3D ACF V3.0 handle?
AORITA3D rates it for 260°C continuous use, with a 305°C melting point.
How many AORITA3D 450x300 sheets are in this listing?
One.
Featured in
See also
- tmypn photon mono x 6k m3 plus screen protector review
- chindrag photon mono 4k ultra d2 integrated fep 2 pack review
- chindrag photon mono x 6ks screen protector 2 pack review
- aorita3d nfep release film 280x200 review
- aorita3d acf release film 280x200 review
- Aorita3D 290x210mm NFEP Film 5-Pack Review (2026)
- kfxjmy 1pcs high performance passive review
- honbay 1pcs stainless steel pasta review
