ANYCUBIC 10.1-Inch ACF Release Film 2-Pack Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
ANYCUBIC's ACF film comes here as two sheets of 278x190mm, 0.3mm thick, with light transmittance of about 95%. ACF is a thicker, stiffer release film than FEP, made to peel cured layers away with less force, which is what lets ANYCUBIC's fast print mode run with its high-speed resin. The fit is where the listing needs care: the title names the Photon Mono M5s, M5s Pro, M7 and M7 Pro, while the first bullet lists only the M5s, M5s Pro and M7 Pro. If you own a plain M7, confirm with ANYCUBIC before buying. One step is easy to miss: the film has an outer protective layer that must be peeled off before installation. ANYCUBIC treats the film as a consumable and says to replace it at once if it deforms or tears. A two-sheet pack suits one printer that needs a replacement and a spare. The points below come from ANYCUBIC's listing and published specs; no sheet was installed for this article.
What stands out
- Two 278x190mm ACF sheets
- 0.3mm thick, about 95% transmittance
- Made for ANYCUBIC fast print mode
- Title and bullets differ on the M7
- Peel the outer protective layer first
Who it fits
Good fit for
Photon Mono M5s, M5s Pro or M7 Pro owners using fast mode who need one replacement film plus a spare.
Who should skip it
Plain M7 owners until ANYCUBIC confirms fit, owners of other 10-inch printers with different vat frames, and anyone re-filming several printers who would save with a bigger pack.
Verdict: The matching ACF for ANYCUBIC's 10.1-inch fast-mode printers, in a small pack.
ANYCUBIC 10.1in ACF film specs
278x190mm
Sheet size for the 10.1-inch Photon Mono vats.
0.3mm thick
Stiffer than typical 0.15mm FEP; this is what lowers peel force.
About 95% transmittance
ANYCUBIC's figure for UV passing through the film.
2 sheets
One to fit now and one in reserve.
Fast mode
Paired with ANYCUBIC's high-speed resin per the listing.
Why ACF on the 10.1-inch Photon Monos
ACF trades a little flexibility for lower suction between the cured layer and the vat floor, so the build plate can lift faster. That is why ANYCUBIC links it to fast mode. Standard FEP or nFEP still works in normal mode on most of these vats, but the listing positions this film for the high-speed setup.
Fitting the ANYCUBIC 278x190 ACF
Clean and drain the vat, remove the worn film, then peel the protective layer from the new ACF sheet before laying it on the frame, as ANYCUBIC notes. Tighten the frame screws evenly, check for leaks before adding resin, and inspect the film after any failed print: a dent or crease means replacing it, per the listing.
Before buying the ANYCUBIC 10.1in ACF 2-pack
Checks.
Check before you buy
- Your printer is a Photon Mono M5s, M5s Pro or M7 Pro
- You run ANYCUBIC fast mode on that 10.1-inch printer
- Two ACF sheets cover your re-film needs
The product at a glance
ANYCUBIC 10.1-Inch ACF Release Film
Best for: Photon Mono fast mode
- Dimensions
- 278x190(mm)
- Release Film Type
- ACF
- Film Thickness
- 0.3mm
- Printing Technology
- Resin
- Features
- High Speed
- Resolution
- 12K, 14K
View on Amazon: ANYCUBIC 10.1-Inch ACF Release Film Affiliate link
Two 278x190mm ANYCUBIC ACF sheets, 0.3mm thick, about 95% transmittance, for Photon Mono M5s/M5s Pro/M7 Pro fast printing.
Pros
- Matches ANYCUBIC fast mode
- Lower peel force than FEP
- Small pack for one printer
Cons
- M7 fit unclear on the listing
- Only two sheets
- No install steps beyond the protective layer note
Good fit if
- You need one ACF sheet plus a spare for an M5s Pro
Skip if
- You re-film several printers at once
Verdict: ANYCUBIC's own fast-mode film for 10.1-inch Photon Monos.
Specifications side by side
| Spec | ANYCUBIC 10.1-Inch ACF Release Film |
|---|---|
| Dimensions | 278x190(mm) |
| Release Film Type | ACF |
| Film Thickness | 0.3mm |
| Printing Technology | Resin |
| Features | High Speed |
| Resolution | 12K, 14K |
| Size | 10.1'' |
Frequently asked questions
Does the ANYCUBIC 10.1-inch ACF film fit the plain Photon Mono M7?
The title lists the M7, but the bullets name only the M5s, M5s Pro and M7 Pro.
How thick is ANYCUBIC's 278x190 ACF film?
0.3mm.
How many ANYCUBIC ACF sheets are in this pack?
Two.
Does the ANYCUBIC ACF sheet have a protective layer?
Yes, an outer layer that must be removed before installation.
Featured in
See also
- shion kwoo creality k2 pet peo build plate review
- aorita3d 450x300mm acf release film v3 review
- tmypn photon mono x 6k m3 plus screen protector review
- anycubic 5pcs 10 1 inch acf high review
- anycubic kobra 3 v2 replacement printhead review
- ANYCUBIC Kobra 3 Max Printhead Assembly Review (2026): A Spec-Based Look
- ANYCUBIC FEP Film 2-Pack for Photon Mono 2 and Mono 4 Review: Specs, Pros and Cons
- ANYCUBIC Kobra 3 USB Monitoring Camera Review: Who It Fits and Who Should Skip It
- venluna 10 1 inch 4k touch review
- evoiron 2 in 1 cordless 10 inch pole review
