As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

ANYCUBIC Kobra 3 Max Printhead Assembly Review (2026): A Spec-Based Look

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

This ANYCUBIC printhead assembly (part FBA-S010304) is the dedicated factory head for the Kobra 3 Max and Kobra 3 Max Combo, the large-format member of the Kobra 3 family. The standard Kobra 3 head does not fit the Max, so Max owners need this one. ANYCUBIC describes industrial-grade materials, calibration for the Max's high-speed, high-flow motion, and a minutes-long install backed by step-by-step videos. Like the standard head's page, it gives no parts list, nozzle size or heater rating. It costs a little over $60 and was low in stock when we checked. Details are from the listing only.

What stands out

  • Made for Kobra 3 Max and Max Combo
  • Original ANYCUBIC part
  • Video install guides
  • Tuned for high-speed motion, per ANYCUBIC

Who it fits

Good fit for

Kobra 3 Max and Kobra 3 Max Combo owners whose print head has failed, been crashed or damaged, and who want a plug-in factory replacement.

Who should skip it

Owners of the standard Kobra 3 or Kobra 3 V2, who need the cheaper S010240 head, and anyone with a fault the nozzle or a fan alone would fix.

Verdict: The correct, if pricey, replacement head for a Kobra 3 Max.

Listing facts

Part FBA-S010304

The ANYCUBIC model code for the Max head.

Kobra 3 Max / Max Combo only

Not interchangeable with the standard Kobra 3 head.

High-speed support

Described as optimized for rapid moves and high flow, without figures.

No spec sheet

Nozzle diameter, heater power and maximum temperature are not stated.

What is known about the build

ANYCUBIC calls it a genuine accessory of wear-resistant, industrial-grade material and promises fewer interruptions. That is the extent of the build detail; no weight, size or contents appear on the page.

Fitting

Cool and power off the printer, disconnect the head cable, unscrew the old unit and mount the new one, then run leveling and a test print. Use ANYCUBIC's video guide for the Max, since cable routing differs from the smaller Kobra 3.

Checks first

Before ordering.

Check before you buy

  • Your printer is a Kobra 3 Max or Max Combo
  • The fault is in the head
  • You can wait out low stock
  • You will recalibrate afterwards

The product at a glance

Anycubic Kobra 3 Max Printhead Assembly

Best for: Kobra 3 Max head replacement

Color
Black
Resin Type
Tough

View on Amazon: Anycubic Kobra 3 Max Printhead Assembly Affiliate link

ANYCUBIC original printhead assembly FBA-S010304 for Kobra 3 Max and Kobra 3 Max Combo; whole-head swap with video guides; no nozzle or heater specs listed.

Pros

  • Correct Max fit
  • Original part
  • Video support

Cons

  • No specs or contents
  • Low stock at our check

Good fit if

  • A crash broke your Kobra 3 Max print head
  • You want a factory replacement

Skip if

  • You own a standard Kobra 3
  • A nozzle swap would do

Verdict: The right head for a Kobra 3 Max repair.

Specifications side by side

Spec Anycubic Kobra 3 Max Printhead Assembly
Color Black
Resin Type Tough
Model FBA-S010304

Frequently asked questions

Does the Kobra 3 Max head fit a standard Kobra 3?

No. It is made for the Kobra 3 Max and Kobra 3 Max Combo; the Kobra 3 uses part S010240.

What is included with the ANYCUBIC Kobra 3 Max printhead?

The listing does not say; contact ANYCUBIC with part FBA-S010304.

How long does the Kobra 3 Max head take to install?

ANYCUBIC says minutes, with step-by-step videos.

Does the Kobra 3 Max printhead list a maximum temperature?

No temperature is given on the listing.

See also