NOVA3D 16K TGM Tough Resin (Beige, 1kg) Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
NOVA3D's 16K TGM resin is a beige 1kg bottle built for board game and tabletop miniatures, where parts get painted, transported and handled. The selling points are toughness and a matte surface you can drill, so pinning arms and magnetizing bases is less likely to crack the figure. NOVA3D says one alcohol wash is enough, the odor is mild, and small supports pull off without damage. One bullet goes further and says the resin needs no post-curing at all, an unusual claim; most users will still give a light cure for a hard, paintable surface. NOVA3D also recommends it for small-scale models rather than big busts or terrain, and it is a 405nm resin for LCD, DLP and SLA printers. There are no exposure times or hardness numbers, though NOVA3D backs the bottle with a one-year warranty and a 12-hour reply promise. Beige gives a warm, bone-like base under paint. We worked from the NOVA3D listing only.
What stands out
- Tough, impact resistant miniature resin
- Matte surface that can be drilled
- One alcohol wash, mild odor
- Beige 1kg, one-year warranty
Who it fits
Good fit for
Tabletop gamers and miniature sellers who pin, magnetize or drill their figures and want them to survive play.
Who should skip it
Printers who want a water-washable resin, large-model resin, or published exposure settings.
Verdict: A miniature-first tough resin with a useful drillable finish; ignore the no-cure claim and test your own cure.
16K TGM beige, in plain terms
Tough, impact resistant
Thin parts are less likely to snap in transport or play.
Drillable matte surface
Pin joints and fit magnets without cracking.
Alcohol wash, one cycle
Not a water-washable resin.
405nm, LCD/DLP/SLA
Suits common resin printers; "16K" refers to fine detail, not a required screen.
Beige, 1kg, one-year warranty
Bone-toned base; NOVA3D promises replies within 12 hours.
What sets TGM apart
Where a standard resin prints sharp but brittle, TGM trades a little stiffness for toughness, and NOVA3D stresses that its matte surface takes drilling and screws. That suits gamers who pin arms or add magnets to swap weapons. The recommendation to keep it to small models is worth taking seriously: tough resins can warp or peel on large flat sections. Beige hides less detail than grey under a camera but gives a warm undercoat.
Printing and finishing TGM beige
Start from a tough resin profile for your screen, as the listing gives no layer times. Wash once in alcohol, let parts dry, then decide on curing: the page says none is needed, but a short cure is the safer route if surfaces stay tacky. Drill pin holes slowly with a hand drill to avoid heat, and keep the bottle shaken and out of light.
Before ordering NOVA3D TGM
A quick check for NOVA3D's beige TGM resin.
Check before you buy
- You print small miniatures rather than large busts in NOVA3D TGM
- You wash NOVA3D TGM prints in alcohol
- You want NOVA3D TGM figures you can drill and pin
The product at a glance
NOVA3D 1KG TGM Tough Resin
Best for: Tabletop minis you pin or magnetize
- Curing Wavelength
- 405nm
- Compatible Technology
- LCD
- Net Weight
- 1kg
- Cleaning Method
- Alcohol
- Application
- Tabletop gaming miniatures
- Printing Technology
- Resin
View on Amazon: NOVA3D 1KG TGM Tough Resin Affiliate link
NOVA3D 16K TGM, beige 1kg: a tough tabletop miniature resin with a drillable matte surface and alcohol cleanup.
Pros
- Drillable for pins and magnets
- Tough for gaming miniatures
- One-year warranty
Cons
- No layer times listed
- Odd no post-cure claim
- Best kept to small models
Good fit if
- You magnetize or pin minis
- You want a warm beige base
Skip if
- You want water cleanup
Verdict: A tough beige miniature resin built for drilling and play.
Specifications side by side
| Spec | NOVA3D 1KG TGM Tough Resin |
|---|---|
| Curing Wavelength | 405nm |
| Compatible Technology | LCD |
| Net Weight | 1kg |
| Cleaning Method | Alcohol |
| Application | Tabletop gaming miniatures |
| Printing Technology | Resin |
| Features | High Speed, High Precision |
| Size | 1KG |
| Resolution | 16K |
| Dimensions | 3.94 × 3.94 × 9 inches |
| Weight | 2.2 pounds |
| Color | Beige |
Frequently asked questions
Is NOVA3D 16K TGM resin water washable?
No, NOVA3D describes cleaning with alcohol.
Does NOVA3D TGM really need no post-cure?
The listing says so; a short cure is still a sensible check if prints feel tacky.
Can you drill NOVA3D TGM beige prints?
Yes, NOVA3D says the matte surface takes drilling and screws without fracturing.
What warranty does NOVA3D TGM resin have?
One year, with replies promised within 12 hours.
