NOVA3D Water Washable ABS-Like Tough Resin (Grey, 1kg) Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
NOVA3D's Water Washable ABS-Like Tough resin tries to combine two things that usually come in separate bottles: a tough, slightly flexible miniature resin and a water-wash cleanup. The grey 1kg bottle is aimed at tabletop figures with thin swords, knives and spears that would snap in a brittle standard resin, and NOVA3D says the supports also come off without breaking delicate parts. Cleanup is a rinse in water instead of IPA, and the cured surface is matte rather than glossy, which reads less like plastic and takes primer well. It is a 405nm resin for 12K and 14K LCD printers as well as DLP and SLA. The listing's post-cure advice is unusually short: cure straight after printing for 30 to 60 seconds, which NOVA3D says keeps the parts flexible. It gives no layer times or hardness, and the "95%+ success rate" comes with the condition that you have tuned your settings first. Everything here is drawn from the listing.
What stands out
- Water wash, no IPA needed
- Tough with flex for thin miniature parts
- Matte grey finish
- Short 30-60 second post-cure
Who it fits
Good fit for
Miniature printers who want tough figures but would rather wash in water than keep a tank of alcohol.
Who should skip it
Users who want listed exposure settings, or who print large, thick parts where a short cure may not reach the core.
Verdict: A practical grey tough resin for minis if you want water cleanup; plan to tune exposure on your own.
NOVA3D WW tough grey, in plain terms
Water washable
Rinse prints in water; no IPA bath.
Tough and flexible
Thin blades and spears bend instead of snapping.
Post-cure 30-60 seconds, right after printing
Short cure that NOVA3D says keeps the flex.
405nm, 12K/14K LCD, DLP, SLA
Fits current high-res resin printers.
Matte grey, 1kg
Shows detail and paints easily.
Water wash and toughness together
Water-washable resins are handy but many cure brittle, and tough resins usually need alcohol to clean. NOVA3D puts both into one grey bottle aimed at miniatures. The matte surface helps for painting, and a low-viscosity formula is said to keep shrinkage down. The weak spots are the missing numbers: no Shore hardness, no elongation and no layer times, so you judge toughness from your own test prints.
Washing and curing NOVA3D WW tough
Rinse in clean water and change it often, since resin-laden water should never go down the drain; let it cure in sunlight and filter it before disposal. Dry parts fully before the cure, then keep that first cure short, as NOVA3D advises 30 to 60 seconds straight after printing. Shake the bottle before each print, and start exposure from a water-washable profile for your screen.
Before ordering NOVA3D WW tough grey
A quick check for this NOVA3D resin.
Check before you buy
- You run a 405nm LCD, DLP or SLA printer for the NOVA3D WW tough resin
- You prefer a water rinse over IPA for NOVA3D grey
- You can find exposure for NOVA3D WW tough without listed settings
The product at a glance
NOVA3D Water Washable ABS-Like Tough Resin 1kg
Best for: Water-wash tough miniatures
- Resin Type
- Water Washable ABS-Like Tough
- Curing Wavelength
- 405nm
- Compatible Technology
- LCD, DLP, SLA
- Net Weight
- 1kg
- Cleaning Method
- Water
- Application
- Miniatures, tabletop game models
View on Amazon: NOVA3D Water Washable ABS-Like Tough Resin 1kg Affiliate link
NOVA3D Water Washable ABS-Like Tough, grey 1kg: a matte miniature resin that rinses in water and keeps some flex.
Pros
- Water cleanup, no IPA
- Flex for thin miniature parts
- Short post-cure step
Cons
- No layer times or hardness data
- Success claim depends on tuned settings
- Rinse water still needs safe disposal
Good fit if
- You print minis with thin weapons
- You want to drop the IPA tank
Skip if
- You need a full datasheet
Verdict: A water-wash tough grey resin aimed at miniatures.
Specifications side by side
| Spec | NOVA3D Water Washable ABS-Like Tough Resin 1kg |
|---|---|
| Resin Type | Water Washable ABS-Like Tough |
| Curing Wavelength | 405nm |
| Compatible Technology | LCD, DLP, SLA |
| Net Weight | 1kg |
| Cleaning Method | Water |
| Application | Miniatures, tabletop game models |
| Printing Technology | Resin |
| Compatible Material | ABS |
| Features | Low Odor, Fast Curing |
| Size | 1KG |
| Resolution | 12K, 14K |
| Dimensions | 3.94 × 3.94 × 7 inches |
| Weight | 2.2 pounds |
| Color | Grey1kg |
| Model | 2002-015-0002-3-USFBA |
Frequently asked questions
Does NOVA3D Water Washable ABS-Like Tough need IPA?
No, NOVA3D says a water rinse is enough.
How long should NOVA3D WW tough grey be post-cured?
The listing recommends 30-60 seconds straight after printing.
Is NOVA3D WW tough resin good for miniatures?
That is its main use: thin parts such as swords and spears are meant to flex rather than break.
Does the NOVA3D grey tough resin dry glossy?
No, the listing describes a matte finish.
