KOYOFEI Ender 3 V3 KE Belt Kit Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This KOYOFEI kit replaces every belt on a Creality Ender 3 V3 KE: an assembled X-axis belt, an assembled Y-axis belt and the ring belt. The listing title uses Creality's name, and KOYOFEI says the belts come from Creality and match the KE's originals, so they go in without cutting or measuring length. That matters on a fast bed slinger like the KE, where a stretched or frayed belt shows up as ringing, layer shifts and corners that are no longer square. KOYOFEI quotes a belt thickness tolerance under 0.01mm, with wear-resistant material and a damped, quiet run. Missing details: belt width, tooth profile, material and lengths. The kit is for the V3 KE alone; the Ender 3 V3 SE, CR-10 SE and Ender 3 S1 have their own KOYOFEI sets. We base this on KOYOFEI's listing and published specs.
What stands out
- X and Y belt assemblies plus ring belt
- Original-length, no cutting
- Under 0.01mm thickness tolerance
- Ender 3 V3 KE only
- Width, pitch and material not listed
Who it fits
Good fit for
Ender 3 V3 KE owners with worn, frayed or stretched belts who want a complete set that drops straight in.
Who should skip it
Owners of the V3 SE, V3 Plus or any other printer, and anyone who wants belt specs before buying.
Verdict: A straight replacement belt set for the V3 KE; check your printer model first.
V3 KE belt kit in plain terms
X-axis belt assembly
Pre-assembled; no length to measure.
Y-axis belt assembly
Pre-assembled for the KE bed axis.
Ring belt
The closed-loop belt in the KE drive.
<0.01mm thickness tolerance
KOYOFEI's figure for even tension along the belt.
Ender 3 V3 KE only
Other Ender 3 V3 models need their own set.
When a V3 KE needs new belts
Signs of a worn belt include ripples beside sharp corners, layer shifts after fast moves and teeth that look shiny or cracked. Because the KE prints quickly, belts carry more load than on older Enders. Replacing all three at once avoids pairing a fresh X belt with a tired Y belt.
Fitting the KOYOFEI V3 KE belts
Since the belts match the original lengths, the job is mostly taking off the old assemblies and fitting the new ones, then setting tension. Check tension with the KE's own procedure and re-run input shaping or resonance tests if your firmware supports it, since new belts change ringing.
Before buying the KOYOFEI V3 KE belt kit
Checks.
Check before you buy
- Your printer is the Ender 3 V3 KE
- You want all three V3 KE belts replaced
- You can retension the V3 KE belts after fitting
The product at a glance
KOYOFEI Ender 3 V3 KE Belt Kit
Best for: Ender 3 V3 KE belt repair
View on Amazon: KOYOFEI Ender 3 V3 KE Belt Kit Affiliate link
KOYOFEI Ender 3 V3 KE belt kit: X and Y belt assemblies plus ring belt, original length, <0.01mm thickness tolerance; no width or pitch listed.
Pros
- All three belts in one kit
- No cutting or measuring
- Tight thickness tolerance
Cons
- Belt width, pitch and material not listed
- Fits the V3 KE only
- Thin five-line listing
Good fit if
- Your V3 KE shows ringing or layer shifts from worn belts
Skip if
- You own a different Ender 3 V3 model
Verdict: A drop-in belt refresh for the Ender 3 V3 KE.
Frequently asked questions
Does the KOYOFEI V3 KE belt kit fit the Ender 3 V3 SE?
No, it is listed for the V3 KE only; a separate V3 SE kit exists.
What belts are in the KOYOFEI V3 KE kit?
An X-axis belt assembly, a Y-axis belt assembly and a ring belt.
Do the V3 KE belts need cutting to length?
No, KOYOFEI says they match the original belts.
Are the KOYOFEI V3 KE belts made by Creality?
The listing says the product comes from Creality and its title uses Creality's name.
See also
- elegoo mars 4 ultra build plate review
- elegoo mars 5 6 6 inch 4k mono LCD review
- elegoo 206x146mm fep release film 5 pack review
- koyofei bambu p1 x1 silicone socks review
- koyofei 5pcs screen protector LCD resin 3d printers review
- KOYOFEI 200x140mm FEP Release Film Review: Who It Fits and Who Should Skip It
- KOYOFEI CR-10 SE Belt Kit Review (2026): A Spec-Based Look
- KOYOFEI 260x200mm FEP Film 6-Pack Review (2026)
- creality ender 3 v3 se review
- gdlepi cineon c35 v3 3 5 inch review
