ELEGOO Mars 4/5/5 Ultra FEP Film 5-Pack (206x146mm) Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
ELEGOO sells this pack as five sheets of 0.15mm FEP release film, each cut to 206x146mm, and names three printers on the title: the Mars 4, Mars 5 and Mars 5 Ultra. That three-printer list is the main reason to pick this listing: a shop or classroom running a mix of Mars machines can keep one box of film for all of them. The bullets claim 95% UV light transmittance, a non-stick and UV-stable surface, and sheets free of wrinkles, scratches and bubbles. A film is a wear part. Each failed print that sticks to the vat floor, each scraper slip and each cloudy patch after long use is a reason to re-film, and five sheets cover several of those events. ELEGOO gives no install steps, screw count or tension method here, and does not say whether the Mars 5 Ultra's tilting vat needs anything different. What follows comes from ELEGOO's own listing and published specs; nobody here fitted a sheet.
What stands out
- Five 206x146mm FEP sheets per box
- 0.15mm thick, 95% UV transmittance claimed
- Names Mars 4, Mars 5 and Mars 5 Ultra
- UV-stable, non-stick surface claimed
- No install steps on the page
Who it fits
Good fit for
Owners of several Mars 4, Mars 5 or Mars 5 Ultra printers, or one busy Mars that goes through film often, who want a stock of matching sheets.
Who should skip it
Saturn, Photon or Halot owners, and anyone who re-films once a year and would rather buy a smaller pack.
Verdict: A practical spare-film stock for the Mars 4/5 family, with no install guidance in the box listing.
ELEGOO Mars FEP 5-pack specs
206x146mm sheet
The cut size for the Mars 4/5 vat frame; measure an older vat before ordering.
0.15mm thickness
A common FEP gauge: thin enough for UV to pass, firm enough to tension.
95% UV transmittance
ELEGOO's figure; cloudier film needs longer exposure.
5 sheets
Enough for several re-films on one printer or one each across a small fleet.
Mars 4 / 5 / 5 Ultra
The three printers the title names; no other models listed.
What the ELEGOO 206x146mm sheets are
The sheets are plain FEP cut to size, with no frame, adhesive or pre-drilled holes mentioned. That means the vat's own clamp ring and screws hold the film, and you set the tension yourself. ELEGOO claims a smooth face without wrinkles or bubbles; check each sheet against light before fitting, since a crease in the print area shows up as a flaw on every layer.
Re-filming a Mars vat with this pack
Drain and clean the vat, remove the old film from its frame, lay a fresh 206x146mm sheet over the frame and tighten the screws evenly in a cross pattern so the film sits flat and taut. A light tap should give a dull drum note. Pour resin only after a leak check with a paper towel under the vat. With five sheets on hand, a punctured or clouded film is a 20-minute job rather than a wait for shipping.
Before buying the ELEGOO Mars 5-pack film
Checks.
Check before you buy
- Your vat is from an ELEGOO Mars 4, Mars 5 or Mars 5 Ultra
- Your Mars vat frame takes a 206x146mm sheet
- You can set FEP tension on a Mars vat by hand
The product at a glance
ELEGOO 5-Pack FEP Release Film
Best for: Mars fleet film stock
- Dimensions
- 206mm*146mm
- Release Film Type
- FEP
- Film Thickness
- 0.15mm
- Printing Technology
- Resin
- Weight
- 7.05 ounces
View on Amazon: ELEGOO 5-Pack FEP Release Film Affiliate link
ELEGOO 0.15mm FEP, five 206x146mm sheets for the Mars 4, Mars 5 and Mars 5 Ultra, with a 95% UV transmittance claim and no install guide on the page.
Pros
- One pack covers three Mars models
- Five sheets for repeat re-films
- 0.15mm gauge stated
Cons
- No install or tension steps
- Tilt-vat notes for the Mars 5 Ultra missing
- Mars family only
Good fit if
- You run more than one Mars 4/5/5 Ultra
Skip if
- Your resin printer is not a Mars
Verdict: A spare-film supply for Mars 4/5 owners.
Specifications side by side
| Spec | ELEGOO 5-Pack FEP Release Film |
|---|---|
| Dimensions | 206mm*146mm |
| Release Film Type | FEP |
| Film Thickness | 0.15mm |
| Printing Technology | Resin |
| Weight | 7.05 ounces |
| Size | 5PCS-Mars 4/5/5 Ultra FEP |
| Color | Mars 4/5/5 Ultra FEP |
Frequently asked questions
Which printers does the ELEGOO 206x146mm FEP 5-pack fit?
The title names the Mars 4, Mars 5 and Mars 5 Ultra.
How thick is the ELEGOO Mars FEP sheet?
0.15mm, per the listing title.
What UV transmittance does ELEGOO claim for this Mars FEP?
95%.
Does the ELEGOO Mars FEP 5-pack include install steps?
The listing gives none; use ELEGOO's vat film guide for your printer.
See also
- ideaformer ir3 v2 0 4mm hardened steel nozzle 5 pack review
- ideaformer kobra 3 max 0 4mm hardened nozzle 2 pack review
- biqu panda aura a1 rgbw light bar review
- elegoo 5pcs pfa film saturn review
- elegoo abs like 3 0 pro clear green resin review
- ELEGOO Metal Resin Tank for Saturn 2 and 3 Review: Specs, Pros and Cons
- ELEGOO Saturn PFA Release Film 2.0 3-Pack Review: Who It Fits and Who Should Skip It
- ELEGOO 3D Printer Adhesive Glue 2-Pack Review (2026): A Spec-Based Look
- tioncy 5 PCs 19 inch review
- uxcell 5 PCs aluminum heat review
