ELEGOO Mars 5 6.6-Inch 4K Mono LCD Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This ELEGOO part (EL-3D-332) is the replacement 6.6-inch 4K mono LCD for the Mars 5 resin printer. The listing gives a resolution of 4098 x 2560 and an XY resolution of 35μm, a lifespan of up to 2000 hours and a factory anti-scratch protector. You buy it when the original screen has dead lines or pixels, cracked glass after a vat leak or a print pressed into it, or simply the end of its hour rating on a busy printer. It is for the plain Mars 5; the Mars 5 Ultra uses a 7-inch 9K panel, a different part. ELEGOO gives no connector type, installation guide or warranty terms on this page, and does not say whether firmware changes are needed. The 4098 figure looks like a typo for the usual 4096-pixel 4K width. Our review comes from ELEGOO's listing and published specs, not from fitting the screen.
What stands out
- Mars 5 replacement screen, 6.6in mono
- 4K, 35μm XY resolution
- Up to 2000 hours rated life
- Anti-scratch protector fitted
- No install guide or connector details
Who it fits
Good fit for
Mars 5 owners whose screen shows dead lines, cracks or failed exposures and who want the matching official panel.
Who should skip it
Mars 5 Ultra owners, owners of other printers, and anyone unwilling to open a printer and handle a ribbon cable.
Verdict: The direct official screen replacement for the Mars 5.
Mars 5 LCD specs
6.6in 4K mono
Same class of panel as the Mars 5 ships with.
35μm XY
ELEGOO's stated pixel pitch for fine detail.
Up to 2000 hours
Rated life; heavy users may reach it within a year or two.
Anti-scratch protector
Protects the glass from scraper slips and debris.
Mars 5 only
Not for the Mars 5 Ultra's 7-inch 9K panel.
Signs a Mars 5 needs a new LCD
Failed prints with the same missing area every time, visible lines on an exposure test, a cracked panel or resin under the protector all point to the screen. Run the printer's exposure test first; if the UV pattern is clean, the problem is more likely the release film or settings.
Swapping the Mars 5 screen
Unplug the printer, remove the vat and drain resin, then follow ELEGOO's Mars 5 screen-replacement steps from its support pages, since this listing includes none. Keep the new panel's protector on, check the ribbon cable seats fully, and run an exposure test before the first print.
Before buying the ELEGOO Mars 5 LCD
Checks.
Check before you buy
- Your printer is the ELEGOO Mars 5, not the Mars 5 Ultra
- An exposure test points to the Mars 5 screen
- You can follow ELEGOO's Mars 5 screen-swap steps
The product at a glance
ELEGOO 6.6" 4K Mono LCD for Mars 5
Best for: Mars 5 screen repair
- Screen Resolution
- 4098 × 2560
- Printing Technology
- Resin
- Dimensions
- 7.52 × 6.18 × 0.43 inches
View on Amazon: ELEGOO 6.6" 4K Mono LCD for Mars 5 Affiliate link
ELEGOO Mars 5 6.6in 4K mono LCD: 35μm XY, up to 2000 hours, anti-scratch protector; Mars 5 only, no install guide on the listing.
Pros
- Official Mars 5 panel
- 35μm XY detail
- Protector fitted
Cons
- Mars 5 only
- No install steps or connector details
- Resolution figure looks mistyped
Good fit if
- Your Mars 5 screen has dead lines or cracks
Skip if
- You own a Mars 5 Ultra
Verdict: The official replacement screen for the Mars 5.
Specifications side by side
| Spec | ELEGOO 6.6" 4K Mono LCD for Mars 5 |
|---|---|
| Screen Resolution | 4098 × 2560 |
| Printing Technology | Resin |
| Resolution | 4K |
| Dimensions | 7.52 × 6.18 × 0.43 inches |
| Size | Mars 5 LCD |
| Model | EL-3D-332 |
Frequently asked questions
Does the ELEGOO 6.6-inch 4K LCD fit the Mars 5 Ultra?
No, the Mars 5 Ultra uses a 7-inch 9K screen.
What resolution is the ELEGOO Mars 5 LCD?
4K, with 35μm XY resolution; the listing writes it as 4098 x 2560.
How long does the Mars 5 replacement screen last?
ELEGOO rates it for up to 2000 hours.
Does the Mars 5 LCD come with a protector?
Yes, an anti-scratch protector is fitted.
See also
- elegoo 206x146mm fep release film 5 pack review
- ideaformer ir3 v2 0 4mm hardened steel nozzle 5 pack review
- ideaformer kobra 3 max 0 4mm hardened nozzle 2 pack review
- elegoo 5pcs pfa film saturn review
- elegoo abs like 3 0 pro clear green resin review
- ELEGOO Metal Resin Tank for Saturn 2 and 3 Review: Specs, Pros and Cons
- ELEGOO Saturn PFA Release Film 2.0 3-Pack Review: Who It Fits and Who Should Skip It
- ELEGOO 3D Printer Adhesive Glue 2-Pack Review (2026): A Spec-Based Look
- healnitor 1200w 6 speed touch LCD review
- upperizon 15 6 4k OLED touchscreen review
