FYSETC 5m GT2 6mm Timing Belt Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The FYSETC 3D Printer Belt is a 5-meter roll of open 2GT timing belt, 6mm wide with a 2mm pitch, the size most Creality Ender, CR-10 and Anet A8 style printers use on X and Y. It is the pick here if you want one cheap roll that covers a full re-belt plus spares. The tooth face uses a treated nylon cloth over rubber that FYSETC says resists wear and slipping; the title also mentions fiberglass reinforcement, which the bullets do not describe further. You cut it to length and clamp the ends with crimp buckles or small zip ties. This summary comes from the listing and published specs only.
What stands out
- 5m of open 2GT belt
- 2mm pitch, 6mm width
- Nylon-faced arc teeth
Who it fits
Good fit for
Owners of Ender 3, Ender 5, CR-10 or i3-style printers replacing worn X/Y belts, or builders who want spare belt on the shelf.
Who should skip it
Printers that use 9mm or 10mm belts, closed-loop belts, or anyone who wants pre-cut lengths with ends ready to fit.
Verdict: A plain, generous roll of standard GT2 6mm belt for routine repairs.
FYSETC belt specifications
Profile 2GT, 2mm pitch
Matches standard GT2 pulleys.
6mm wide
Common Ender/CR-10 size.
5m (196.8in) long
Several axes from one roll.
Rubber body, nylon tooth cloth
Listed wear protection.
Open belt, cut to size
Ends clamp at the carriage.
Model US-5M Open Belt
Listing model code.
Belt construction
Arc-shaped teeth sit in GT2 pulleys with less backlash than older trapezoid profiles, which is why this shape is standard on hobby printers. FYSETC describes an anti-stretch, anti-jump build and a cloth-covered tooth face for longer life. Fiberglass appears only in the product title, so treat the core material as unconfirmed.
Fitting a new GT2 belt
Measure the old belt or route a string along the axis before cutting, then leave a few centimeters spare for the clamp. Tension until the belt gives a low note when plucked and the axis moves without skipping; too tight wears the idler bearings. Choose this 5m roll if you are replacing both X and Y or want spares; a short 2m roll is enough for a single axis.
Before you order
Checks for the FYSETC GT2 belt roll.
Check before you buy
- Your printer uses 6mm GT2 belt, not 9mm or 10mm
- The pulleys have 2mm pitch teeth
- You have clamps, crimps or zip ties for the ends
- You want an open belt, not a closed loop
The product at a glance
FYSETC 5M 2mm Pitch 6mm Wide Belt
Best for: Re-belting bed slingers
- Primary Material
- Rubber, fiberglass reinforced
- Belt Pitch
- 2mm Pitch
- Dimensions
- 1.97 × 0.24 × 0.08 inches
- Weight
- 1.59 ounces
View on Amazon: FYSETC 5M 2mm Pitch 6mm Wide Belt Affiliate link
FYSETC open GT2 timing belt, 5m roll, 2mm pitch, 6mm wide, rubber with nylon-faced teeth, cut to fit.
Pros
- Long 5m roll
- Standard GT2 6mm size
- Wear-resistant tooth cloth
Cons
- Core reinforcement not described
- No clamps or crimps listed
Good fit if
- You are re-belting an Ender or CR-10
- You want spare belt
Skip if
- Your printer uses 9mm or 10mm belts
Verdict: A low-cost GT2 roll for repairs.
Specifications side by side
| Spec | FYSETC 5M 2mm Pitch 6mm Wide Belt |
|---|---|
| Primary Material | Rubber, fiberglass reinforced |
| Belt Pitch | 2mm Pitch |
| Dimensions | 1.97 × 0.24 × 0.08 inches |
| Weight | 1.59 ounces |
| Size | 196.8 inches |
| Color | 5M |
| Model | US-5M Open Belt |
Frequently asked questions
What printers does the FYSETC belt fit?
Printers with 6mm GT2 belts, such as Ender 3, Ender 5, CR-10 and Anet A8 models named in the listing.
How long is the FYSETC belt roll?
5 meters, about 16.4 feet.
Is the FYSETC belt open or closed?
Open; you cut it and clamp the ends.
What is the belt made of?
Rubber with a nylon cloth tooth face; the title also mentions fiberglass reinforcement.
Can one roll replace both X and Y belts?
On most bed slingers, yes, with length to spare.
Featured in
See also
- capricorn xs 1m ptfe tube kit review
- polisi3d cr 10s pro dual gear extruder review
- zeelo 10m gt2 6mm timing belt review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- ideaformer 3d conveyor belt 3d printer review
- unxuey 50pcs 3d printer heatsink review
