Capricorn XS 1m PTFE Tube Kit Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This kit pairs 1 meter of Capricorn XS Series PTFE tubing for 1.75mm filament with four push-fit couplers and a tube cutter, so it covers a complete Bowden refresh on an Ender 3, Ender 3 V2, Ender 5 or CR-10 in one order. Capricorn tube is known for a tight bore that guides filament with little slack, which helps with retraction and softer materials. The listing claims XS is rated for higher heat than standard PTFE and names ABS, nylon and polycarbonate as targets. It does not print the inner or outer diameter of the tube itself, only that the fittings take 4mm OD tube. Everything here is drawn from the listing and published specs.
What stands out
- 1m Capricorn XS tube
- 2x PC4-M6 + 2x PC4-M10 couplers
- Razor tube cutter included
Who it fits
Good fit for
Ender 3, Ender 5 and CR-10 owners whose Bowden tube is worn, loose in its couplers, or causing stringing and under-extrusion.
Who should skip it
Direct drive printers, all-metal setups that need no PTFE, or printers with a Bowden longer than about 1 meter.
Verdict: A sensible all-in-one Bowden refresh with name-brand tube.
Capricorn XS kit contents
Capricorn XS tube, 1m
For 1.75mm filament.
PC4-M6 couplers x2
Extruder side, M6 thread.
PC4-M10 couplers x2
Hotend side, M10 thread.
Fittings take 4mm OD tube
Tube ID not stated.
Cutter with spare-sharp razor
Square, flat cuts.
Higher heat rating claimed
No figure given.
Why the fittings matter
Worn couplers let the tube creep back during retraction, opening a gap at the nozzle where filament pools and jams. Fresh PC4-M6 (extruder) and PC4-M10 (hotend) fittings fix that alongside the tube. The PC4-M6 parts are copper and plastic, the PC4-M10 parts stainless steel and plastic, per the listing.
Installing the XS tube
Cut the tube square with the included cutter, push it fully down to the nozzle on the hotend side, then lock the couplers. A slanted cut leaves a gap that causes heat creep and clogs, which is why the cutter is part of the kit. Choose this 1m kit for a single Ender-size Bowden with new fittings; a longer roll without fittings suits bigger printers or several spares.
Before you order
Checks for the Capricorn XS PTFE kit.
Check before you buy
- Your printer uses 1.75mm filament in a Bowden setup
- The extruder takes PC4-M6 and the hotend PC4-M10 fittings
- Your Bowden run is under 1 meter
- You do not need a stated tube inner diameter
The product at a glance
Sovol Capricorn XS 1m PTFE Tubing
Best for: Ender Bowden refresh
- Primary Material
- PTFE
- Extruder Type
- Bowden Extruder
- Length
- 1 meters
View on Amazon: Sovol Capricorn XS 1m PTFE Tubing Affiliate link
Capricorn XS Series Bowden tube, 1m for 1.75mm, with two PC4-M6, two PC4-M10 couplers and a PTFE cutter.
Pros
- Tight-bore Capricorn tube
- Both coupler types included
- Cutter for square ends
Cons
- Tube ID and heat rating not stated
- Only 1m of tube
Good fit if
- You have an Ender or CR-10 Bowden
- Your couplers are worn
Skip if
- Your printer is direct drive
Verdict: A full Bowden refresh in one box.
Specifications side by side
| Spec | Sovol Capricorn XS 1m PTFE Tubing |
|---|---|
| Primary Material | PTFE |
| Extruder Type | Bowden Extruder |
| Length | 1 meters |
| Size | 1 Meter |
| Color | multi-color |
Frequently asked questions
Which printers does this Capricorn kit fit?
Creality Ender 3, Ender 3 V2, Ender 3 Pro, Ender 5, CR-10 and CR-10S, per the listing.
How much tube comes in the kit?
1 meter of Capricorn XS Series tubing.
Which fittings are included?
Two PC4-M6 for the extruder and two PC4-M10 for the hotend.
Is a cutter included?
Yes, a PTFE cutter with a sharp razor.
What is the tube's inner diameter?
The listing does not state it; the fittings take 4mm OD tube.
Featured in
See also
- polisi3d cr 10s pro dual gear extruder review
- zeelo 10m gt2 6mm timing belt review
- zeelo dual drive aluminum extruder review
- sovol creality capricorn 2 meters review
- sovol 3d printer tools kit review
- Sovol SV08 Max Metal and Glass Enclosure Review: Specs, Pros and Cons
- Sovol 5-Inch IPS50 HDMI Touch Screen for SV08 Review: Who It Fits
- Sovol SV08 Metal and Tempered Glass Enclosure Review (2026)
- sovol sv08 max corexy 3d printer review
- best towable tubes for tubing
