As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

Creality Ender 3 V3 / V3 Plus Hotend Adapter Board Review (2026)

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

This is not a printer: it is Creality's official hotend adapter board (the small circuit board on the print head) for the Ender 3 V3 and Ender 3 V3 Plus. The listing title carries the part code T9_GD32F303CBT6_1, which names the GD32F303 microcontroller on the board. You would buy it when the toolhead board has failed, for example after a shorted heater or thermistor plug, or when temperature readings jump and cause clogs or layer splits. Its strongest point is the install: Creality says it comes with firmware loaded and fits in about five minutes following the original instructions, with no soldering. Creality also claims tighter temperature control, good resistance to interference and heat, and stable output for PLA, ABS and PETG. It gives no connector list, board size or revision notes. We based this on Creality's listing, without fitting the part ourselves.

What stands out

  • Official part for Ender 3 V3 and V3 Plus
  • Firmware pre-installed
  • About 5-minute swap, per Creality
  • GD32F303 chip named in part code

Who it fits

Good fit for

Ender 3 V3 and V3 Plus owners with a faulty or damaged print-head board who want the original part back with the least fuss.

Who should skip it

Ender 3 V3 SE, KE or older Ender 3 owners; the listing names only the V3 and V3 Plus.

Verdict: The straightforward fix for a dead Ender 3 V3 or V3 Plus toolhead board; buy only if the board is the fault.

Ender 3 V3 hotend adapter board, decoded

Fits Ender 3 V3 / V3 Plus

Original specifications, per Creality.

T9_GD32F303CBT6_1

Part code; GD32F303 is the board's microcontroller.

Pre-installed firmware

No flashing step before use.

PLA, ABS, PETG

Materials Creality says the board handles.

No connector or size data

Match it to your board by photo and code.

What the board does

The adapter board links the hotend heater, thermistor, fans and other print-head parts to the mainboard through one cable. When it fails, symptoms include temperature errors, fans that stop, or a hotend that will not heat. Creality points to its chip and PCB build for steadier temperature readings and better heat and interference resistance than generic parts.

Fitting the Ender 3 V3 adapter board

Power the printer down and unplug it first. Photograph each connector on the old board, move them across one at a time and refit the cover. Creality says no technical skill is needed and that the firmware is already on the board, so the printer should run once reconnected. Run a PID tune and a test print afterwards.

Before buying the Ender 3 V3 adapter board

Checks.

Check before you buy

  • Your printer is an Ender 3 V3 or Ender 3 V3 Plus, not a V3 SE or KE
  • The fault is the toolhead board, not the hotend or ribbon cable
  • The code on your Ender 3 V3 board matches T9_GD32F303CBT6

The product at a glance

Creality Ender 3 V3 and V3 Plus Hotend Adapter Plate

Best for: Ender 3 V3 / V3 Plus repairs

View on Amazon: Creality Ender 3 V3 and V3 Plus Hotend Adapter Plate Affiliate link

Creality Ender 3 V3 / V3 Plus hotend adapter board: the official toolhead board, pre-flashed, with a quick swap and claimed steadier temperature control.

Pros

  • Official Creality part
  • No firmware flashing
  • Quick, solder-free swap

Cons

  • No connector list or board size
  • Fits only V3 and V3 Plus
  • Claims are unquantified

Good fit if

  • Your V3 or V3 Plus head board has failed

Skip if

  • You own a V3 SE or KE

Verdict: The clean fix for a failed V3 head board.

Specifications side by side

Spec Creality Ender 3 V3 and V3 Plus Hotend Adapter Plate
Color Ender 3 V3 Plus Hotend Adapter Plate

Frequently asked questions

Does this Creality adapter board fit the Ender 3 V3 SE?

The listing names only the Ender 3 V3 and Ender 3 V3 Plus.

Do I need to flash firmware on the Ender 3 V3 adapter board?

No, Creality says the firmware is pre-installed.

How long does the Ender 3 V3 board swap take?

Creality says about five minutes following the original instructions.

What does GD32F303 mean in the part code?

It is the microcontroller fitted on the board.

See also