Creality 310x320mm Textured PEI Build Plate Review: Specs, Pros and Cons
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This is Creality's official 310x320mm build surface: a gold frosted PEI sheet on flexible spring steel plus a self-adhesive magnetic sticker for the bed. It replaces glass or a worn mat on the Ender-3 Max and Max Neo, CR-10 V2 and V3, CR-10S Pro (and V2), CR-X and CR-X Pro, which all share this bed size. Prints come off by flexing the sheet, and the textured PEI needs no glue or tape. At around $30 it is a cheap upgrade for an older large-bed Creality. Everything here comes from Creality's listing, not our own prints.
What stands out
- Fits seven 310x320mm Creality beds
- Textured gold PEI, no glue needed
- Flex the steel to release prints
- Magnet sticker included
Who it fits
Good fit for
Owners of an Ender-3 Max, Ender-3 Max Neo, CR-10 V2/V3, CR-10S Pro or CR-X who still print on glass or a stock mat and want easier part removal and a textured underside.
Who should skip it
Anyone with a 235x235mm Ender bed or a newer K-series printer: the size is wrong. Owners who prefer a glossy bottom finish should look at smooth PEI instead.
Verdict: A low-cost, well-matched surface swap for Creality's 310x320mm printers.
Plate details explained
310x320mm
The bed size shared by the Ender-3 Max line, CR-10 V2/V3, CR-10S Pro and CR-X.
Textured gold PEI
Grips the first layer while warm, releases as it cools, and leaves a frosted underside.
Spring steel plus magnet sticker
The sticker bonds to the bed with 3M adhesive; the sheet sits on it magnetically.
Heated-bed use
Creality calls the coating heat- and flame-resistant; it gives no maximum bed temperature.
Material list needs a pinch of salt
The listing says PLA, PETG, ABS and even PEEK work on it. PEI handles the first three on these printers; PEEK needs hotend and chamber temperatures none of the named Creality printers reach, so treat that line as marketing. No coating thickness or maximum temperature is given.
Fitting and daily use
Creality quotes under two minutes to fit: peel the backing, stick the magnet sheet onto a cold, clean bed, then lay the steel plate on top. Re-level and reset the Z offset after the swap, because the new surface sits at a different height than the old one. Keep fingers and grease off the PEI so the first layer grips evenly.
Before you order
Quick checks.
Check before you buy
- Your bed measures 310x320mm
- Your bed is cold when you apply the sticker
- You are fine with a textured underside
- You will re-run bed leveling afterwards
The product at a glance
Creality 310x320mm Textured PEI Build Plate
Best for: 310x320mm Creality beds
- Primary Material
- Spring Steel
- Dimensions
- 310 x 320 mm
- Build Surface Type
- Textured PEI
View on Amazon: Creality 310x320mm Textured PEI Build Plate Affiliate link
Creality's official 310x320mm gold textured PEI spring-steel sheet with a 3M-backed magnet sticker, for Ender-3 Max/Max Neo, CR-10 V2/V3, CR-10S Pro and CR-X beds.
Pros
- Correct size for large Creality beds
- Glue-free textured PEI
- Magnet base included
Cons
- No max temperature listed
- PEEK claim is unrealistic
Good fit if
- You print on glass on an Ender-3 Max Neo
- You want flex-off part removal
Skip if
- Your bed is 235x235mm
- You want a glossy underside
Verdict: A cheap, correct-size PEI upgrade for 310x320mm Creality beds.
Specifications side by side
| Spec | Creality 310x320mm Textured PEI Build Plate |
|---|---|
| Primary Material | Spring Steel |
| Dimensions | 310 x 320 mm |
| Build Surface Type | Textured PEI |
| Build Plate Material | PEI |
| Surface Finish | Textured |
| Size | Ender 3 Max Neo |
| Color | PEI Frosted Gold |
| Model | 3D-PEI-320x310 |
If you are also weighing heated surfaces for other workshop tasks, our cusimax hot plate review covers that product's published specifications in the same format.
Frequently asked questions
Does the Creality 310x320mm PEI sheet fit an Ender-3 V3?
No. The Ender-3 V3 family uses smaller beds; this sheet lists the Ender-3 Max, Max Neo, CR-10 V2/V3, CR-10S Pro and CR-X.
Is a magnetic base included with this Creality PEI plate?
Yes, the kit is the gold PEI plate plus a soft magnetic sticker for the bed.
Can I really print PEEK on this textured PEI sheet?
The listing says so, but PEEK needs far higher temperatures than the listed printers reach.
Do I need glue on the gold textured PEI?
Creality says no tape or glue is needed.
