Comgrow 235x235mm PEO/PEI Build Plate Review: Who It Fits and Who Should Skip It
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This Comgrow accessory is a 235x235mm magnetic spring steel plate that pairs two coatings: a smooth PEO face for glossy bottoms and a gold-tinted textured PEI face for grip. Comgrow suggests the PEO face for PLA and TPU, rating that coating to 120°C; the PEI coating covers PLA, PETG, ABS, ASA, TPU, nylon and PC. Prints release when you flex the sheet, and two handles plus two locating holes help it sit squarely. At $13.99 it suits Ender-3 V3 SE owners and many other 235mm beds. Details come only from Comgrow's listing.
What stands out
- Two surfaces on one sheet
- Flex to release prints
- Handles and locating holes
- Long fit list of 235mm printers
Who it fits
Good fit for
Owners of 235mm-bed machines such as the Ender-3 V3 SE or KE, K1 or K1C, or the Neptune 4 series who want one plate covering both glossy-bottom PLA and grippy PETG or ABS prints.
Who should skip it
Look elsewhere when the bed is another size or lacks a magnetic base, since the listing only describes the steel sheet itself.
Verdict: A cheap two-in-one bed upgrade for 235mm printers, with clear guidance on which face suits which filament.
Plate specs explained
Smooth PEO side, 120°C rated
Gives a flat, glossy underside; Comgrow recommends it for PLA and TPU.
Textured gold PEI side
A matte grip surface that tolerates repeated heat cycles and wider filament choice.
235x235mm magnetic spring steel
Sticks to a magnetic bed and bends slightly so parts pop free.
Dual handles, dual positioning holes
Make it easier to lift off and to place in the same spot each time.
Two faces, two jobs
The PEO face is flat and smooth, aimed at PLA and TPU when you want a shiny base. Turn the sheet over and the textured PEI face handles hotter work, with Comgrow listing PETG, ABS, ASA, nylon (PA) and PC alongside PLA and TPU. The listing also stresses flatness and says the sheet resists deforming after repeated bending.
Using the plate
Lay it on your magnetic base, lining up the locating holes, and re-check the Z offset since a new surface can sit at a different height. Choose the face by filament, let the plate cool a little after printing, then lift it by a handle and flex it to free the part. Comgrow never mentions a magnetic base in the box; machines like the Ender-3 V3 SE already carry one.
Before you buy this PEO/PEI plate
Confirm the bed, then the base.
Check before you buy
- Your bed is 235x235mm
- A magnetic base is already on your bed
- You print PLA plus PETG or ABS
- Your machine appears in the fit list
The product at a glance
Comgrow 235x235mm PEO and PEI Build Plate
Best for: 235mm beds printing mixed filaments
- Primary Material
- spring steel
- Dimensions
- 235X235mm
- Maximum Temperature
- 120°C
- Build Surface Type
- Smooth PEO and Textured PEI
- Build Plate Material
- PEI, Spring Steel, PEO
View on Amazon: Comgrow 235x235mm PEO and PEI Build Plate Affiliate link
Comgrow's $13.99 two-coating 235x235mm steel sheet (PEO smooth, PEI textured) suits Ender-3 V3 SE, K1 and Neptune 4 class beds.
Pros
- PEO and PEI in one plate
- Clear filament guidance per side
- Handles and locating holes
Cons
- No magnetic base mentioned
- 235mm beds only
- PEO side meant for PLA and TPU only
Good fit if
- Your printer is an Ender-3 V3 SE, KE, K1 or Neptune 4
- You switch between PLA and PETG often
Skip if
- Your bed has no magnetic base
- Your bed is not 235mm
Verdict: A versatile, low-cost plate for 235mm magnetic beds.
Specifications side by side
| Spec | Comgrow 235x235mm PEO and PEI Build Plate |
|---|---|
| Primary Material | spring steel |
| Dimensions | 235X235mm |
| Maximum Temperature | 120°C |
| Build Surface Type | Smooth PEO and Textured PEI |
| Build Plate Material | PEI, Spring Steel, PEO |
| Build Plate Size | 235x235mm |
| Surface Finish | Smooth, Textured |
| Size | 235*235 for For Ender 3 V3 KE |
Frequently asked questions
Which side should I use for PLA?
Either works; Comgrow points PLA and TPU to the smooth PEO side.
Can I print ABS or nylon on it?
Yes, on the textured PEI side, according to the listing.
Does it fit the Ender-3 V3 SE?
Yes. It is listed, along with K1, K1C, Neptune 3 Pro, Neptune 4 and many Ender 3 and Ender 5 models.
Is a magnetic sticker included?
The listing does not say so; plan to use your printer's existing magnetic base.
Featured in
See also
- comgrow petg filament review
- longer lk5 pro 3 3d printer review
- longer lk10 plus 3d printer review
- comgrow 235mm magnetic build surface review
- comgrow 25pcs mk8 ender 3 review
- Creality CR Touch Auto Bed Leveling Kit Review: Who It Fits and Who Should Skip It
- Comgrow 235x235mm Textured PEI Spring Steel Sheet Review (2026)
- Comgrow 24-Piece MK8 Brass Nozzle Kit Review (2026)
- creality ender 3 v3 se review
- gdlepi cineon c35 v3 3 5 inch review
