Yousu PEBA-Like 95A Super TPU Review: Who It Fits and Who Should Skip It
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Yousu PEBA-Like 95A is a flexible filament sold as a step beyond TPU: Yousu quotes 78% energy return, over 30% more than standard TPU, and a density 20% lower, so prints bounce back harder and weigh less. That makes it a fit for airless balls, lattice insoles, shock absorbers, robot joints, drone parts and wearables. Its nylon-based backbone adds fatigue resistance, and it stays flexible down to -60°C with resistance to oils and solvents. It is demanding to print: dry at 80°C for 8-12 hours, print at 230°C nozzle and 40-80mm/s, retraction no more than 1.4mm, on a direct-drive extruder fed from a dry box. The details come from Yousu's listing.
What stands out
- 78% energy return, 20% lighter than TPU
- Shore 95A, flexible to -60°C
- Full print and drying settings given
Who it fits
Good fit for
Makers of bouncy or shock-absorbing parts (sports balls, insoles, robot feet and joints, drone bumpers) who own a direct-drive printer and a filament dryer.
Who should skip it
Owners of Bowden printers, anyone without a dryer or dry box, and buyers who just need ordinary flexible parts, where standard 95A TPU is easier and cheaper.
Verdict: A specialist flexible filament for parts that must rebound; it rewards careful drying and slow, direct-drive printing.
Yousu PEBA-Like 95A specs
78% energy return
Springier rebound than standard TPU, per Yousu.
20% lower density than TPU
Lighter parts for drones, robots and wearables.
Flexible to -60°C, oil and solvent resistant
Holds up in cold and around grease.
Nozzle 230°C, bed 35-65°C, fan 30-70%
Moderate temperatures; the bed range is wide.
40-80mm/s, retraction 1.4mm max
Slow and gentle, as with most flexibles.
Pre-dry 80°C for 8-12 hours
Highly hygroscopic; print from a dry box.
The spool
A 1kg (2.2 lb) orange spool of 1.75mm PEBA-like filament. Yousu calls it nylon-based for strength with elastomer flexibility. The listing gives Shore 95A in the name but no tensile or elongation figures.
Printing PEBA-like filament
Dry the spool at 80°C for 8-12 hours, then feed it from a dry box into a direct-drive extruder with dual gears. Print at 230°C on a 35-65°C bed, 40-80mm/s, part fan 30-70%, and keep retraction at 1.4mm or less to avoid jams. Store it sealed with desiccant between prints; Yousu stresses that PEBA picks up moisture quickly.
Before you buy
PEBA-Like 95A checklist.
Check before you buy
- Your printer has a direct-drive dual-gear extruder
- You own a dryer that holds 80°C
- You can print PEBA-like parts from a dry box
- Your part needs rebound, not just flex
The product at a glance
Yousu PEBA-Like 95A Super TPU
Best for: Rebound parts
- Material Type
- TPU
- Filament Diameter
- 1.75 mm
- Net Weight
- 1 kg
- Shore Hardness
- 95A
- Compatible Material
- TPU, Nylon
- Weight
- 2.2 pounds
View on Amazon: Yousu PEBA-Like 95A Super TPU Affiliate link
Yousu PEBA-Like 95A, orange, 1.75mm, 1kg: 78% energy return, 20% lower density than TPU, flexible to -60°C, oil/solvent resistant; 230°C nozzle, 35-65°C bed, 40-80mm/s, retraction ≤1.4mm; dry 80°C 8-12h; direct drive.
Pros
- High rebound
- Lighter than TPU
- Full settings published
Cons
- Needs thorough drying
- Direct drive only
Good fit if
- You print balls, insoles or robot joints
- You own a dryer and direct-drive printer
Skip if
- You use a Bowden printer
Verdict: A bouncy, light flexible filament for rebound parts.
Specifications side by side
| Spec | Yousu PEBA-Like 95A Super TPU |
|---|---|
| Material Type | TPU |
| Filament Diameter | 1.75 mm |
| Net Weight | 1 kg |
| Shore Hardness | 95A |
| Compatible Material | TPU, Nylon |
| Weight | 2.2 pounds |
| Size | F-PEBA-Like |
| Color | F4-peba-like Orange 1kg |
Frequently asked questions
What is PEBA-like filament?
A flexible filament with a nylon-based backbone that Yousu says returns 78% of energy and is 20% lighter than TPU.
What settings does Yousu PEBA-Like 95A use?
Nozzle 230°C, bed 35-65°C, fan 30-70%, 40-80mm/s, retraction 1.4mm or less.
Does Yousu PEBA-Like need drying?
Yes: 80°C for 8-12 hours before printing, then a dry box during printing.
Can Yousu PEBA-Like 95A print on a Bowden printer?
Yousu calls for a direct-drive extruder; Bowden setups are not recommended.
PEBA-like or standard 95A TPU?
Choose PEBA-like for bouncy, lightweight parts such as balls, insoles and robot joints; choose standard TPU for cases, gaskets and grips where rebound does not matter.
See also
- mika3d glow in the dark rainbow pla review
- mika3d 12 spool silk pla filament bundle review
- flashforge petg pro filament 1 75mm review
- yousu 3d printer filament review
- yousu silk pla filament 1 75mm review
- Yousu PETG 1.75mm 5kg Filament Review: Specs, Pros and Cons
- YOUSU Transparent PETG Filament (1kg) Review (2026)
- YOUSU Glow in the Dark PLA 4x250g Pack Review
- fungdo LCD 3d printer review
- easycargo 30pcs 3d printer heatsink review
