TIEXYE GT2 2m 6mm Timing Belt Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
A 2-meter length of 6mm GT2 belt covers both X and Y on most Ender 3 printers, which is why TIEXYE sells it with four copper sleeves to crimp the ends. The belt has a 2mm pitch and comes open, so you cut it to the length each axis needs. TIEXYE names the Ender 3, Ender 3 Pro, V2, S1, S1 Pro, V3 SE and V3 KE, the Ender 5 series and the CR-10 series. The listing is short on material: it says the belt is soft, wear and crack resistant, but gives no fiberglass or steel core and no tooth profile beyond GT2. For a stretched or frayed stock belt on a Creality printer it is a cheap fix. These notes follow TIEXYE's listing only.
What stands out
- 2m of open GT2 belt, 6mm wide
- Four copper sleeves
- Named for Ender and CR-10 printers
Who it fits
Good fit for
Creality Ender and CR-10 owners replacing a worn X or Y belt on a budget.
Who should skip it
Anyone who wants a stated reinforcement material, or a 10mm belt for a wider axis.
Verdict: A cheap, adequate belt roll for Creality printers; the material is not specified.
TIEXYE GT2 belt specs
2 meters
Enough for two axes on an Ender 3.
6mm wide
Standard Creality width.
2mm pitch
GT2 profile.
4 copper sleeves
Crimp the belt ends.
Open belt
Cut to length.
Reinforcement
Not stated.
Belt and sleeves
An open belt is cut to length and its ends are looped through the carriage, where the copper sleeves hold the loop tight once crimped. Four sleeves cover two belts. Count the teeth on the old belt or measure it before cutting, since a belt cut short cannot be stretched back.
Fitting and tension
After fitting, tension the belt until it gives a low tone when plucked and does not skip under fast moves; over-tightening wears the idlers and motor bearings. Choose the TIEXYE roll if you need one length with sleeves at a low price; choose a belt that lists a fiberglass core if you run high accelerations and want less stretch.
Before you order
Checks for the TIEXYE GT2 belt.
Check before you buy
- Your printer uses 6mm GT2 belt
- Two meters covers your axes
- You have pliers to crimp the sleeves
- You accept no stated core material
The product at a glance
TIEXYE GT2 2m 6mm Belt
Best for: Creality belt repairs
- Belt Pitch
- 2mm Pitch
View on Amazon: TIEXYE GT2 2m 6mm Belt Affiliate link
TIEXYE 2m open GT2 belt, 6mm wide, 2mm pitch, with four copper sleeves for Ender and CR-10 printers.
Pros
- Low price
- Sleeves included
- Covers two axes
Cons
- Core material not stated
- Generic durability claims
Good fit if
- You own an Ender 3 or CR-10
- You want a spare roll
Skip if
- You need a 10mm belt
Verdict: Fine for routine belt replacement.
Specifications side by side
| Spec | TIEXYE GT2 2m 6mm Belt |
|---|---|
| Belt Pitch | 2mm Pitch |
Frequently asked questions
How long is the TIEXYE belt?
2 meters, open, cut to the length you need.
What width and pitch is the TIEXYE belt?
6mm wide with a 2mm GT2 pitch.
What comes with the TIEXYE belt?
Four copper sleeves for securing the belt ends.
Which printers does TIEXYE list?
Ender 3 models including V2, S1, S1 Pro, V3 SE and V3 KE, the Ender 5 series and the CR-10 series.
Is the TIEXYE belt fiberglass reinforced?
The listing does not say.
Featured in
See also
- jinshining ender 3 v2 xy timing belt kit review
- dorundea resin printer enclosure fan filter review
- ideaformer neptune 4 plus max 22pc nozzle kit review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- ideaformer 3d conveyor belt 3d printer review
- jet 2 x 42 belt review
