Jinshining Ender 3 V2 X/Y Timing Belt Kit Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Jinshining sells this as a matched X and Y belt pair for the Creality Ender 3 V2 rather than a roll you cut yourself. The belts are 2GT with a 6mm width, made of black rubber composite with a reinforced core. That is the right profile for the V2, which uses 6mm GT2 on both axes. The listing leaves out details you would want to check: it gives no belt lengths, does not say whether the belts come cut, looped or with ends prepared, and does not name the core material. Buy it if you own a V2 and want both belts replaced at once without measuring a roll. Everything here is drawn from Jinshining's listing.
What stands out
- Matched X and Y belts
- 2GT profile, 6mm wide
- Made for the Ender 3 V2
Who it fits
Good fit for
Ender 3 V2 owners who want both axis belts replaced in one order.
Who should skip it
Owners of other printers, and anyone who needs belt lengths or a stated core material before buying.
Verdict: Convenient for a V2 refresh, but the listing is thin on specifics.
Jinshining belt kit specs
Ender 3 V2
Only printer named.
X and Y belts
Both axes in one kit.
2GT, 6mm
Belt profile and width.
Rubber composite
Black, with a reinforced core.
Lengths
Not stated.
Core material
Not stated.
A pair for one printer
On the Ender 3 V2 the X belt runs along the gantry and the Y belt under the bed, and both wear at the idlers over time. Replacing them together keeps the tension feel similar on both axes. Since the listing does not give lengths, lay the delivered belts next to the worn ones before taking anything apart, and keep the worn pair until the new ones run.
Fitting on the V2
Loosen the tensioner knobs, release the belt ends at the carriage and the bed, and route the new belt the same way. Tension each axis until it no longer sags. Choose the Jinshining pair if you have a V2 and want a ready-made set; choose a 2m open belt roll with sleeves if you own another Ender model or want spare length.
Before you order
Checks for the Jinshining V2 belt kit.
Check before you buy
- Your printer is an Ender 3 V2
- You will compare lengths before fitting
- A Jinshining core of unnamed material is fine
- You have a hex key for the tensioners
The product at a glance
Jinshining 2GT-6mm Black Timing Belt
Best for: Ender 3 V2 owners
- Primary Material
- Rubber composite
View on Amazon: Jinshining 2GT-6mm Black Timing Belt Affiliate link
Jinshining X and Y 2GT 6mm belt pair for the Ender 3 V2, rubber composite with a reinforced core.
Pros
- Both axes in one kit
- Correct 6mm 2GT for the V2
Cons
- No lengths listed
- Core material not named
Good fit if
- You own an Ender 3 V2
- You want both belts at once
Skip if
- You own another printer
Verdict: A handy V2 pair if you can live with the vague listing.
Specifications side by side
| Spec | Jinshining 2GT-6mm Black Timing Belt |
|---|---|
| Primary Material | Rubber composite |
Frequently asked questions
Which printer is the Jinshining belt kit for?
The Creality Ender 3 V2.
Does the Jinshining kit include both belts?
Yes, one for the X axis and one for the Y axis.
What belt type does Jinshining use?
2GT with a 6mm width.
How long are the Jinshining belts?
The listing does not state the lengths.
What are the Jinshining belts made of?
Black rubber composite with a reinforced core; the core material is not named.
See also
- dorundea resin printer enclosure fan filter review
- ideaformer neptune 4 plus max 22pc nozzle kit review
- chindrag mono 2 mono 4 integrated fep film review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- nikon black review
- arctic xtender black review
