JAYO PETG Filament Review: Specs, Pros and Cons
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
JAYO's green PETG comes on a 1.1kg reusable spool, 100g more than the usual kilo, for under $15, which makes it one of the cheaper ways to stock up on PETG. JAYO pitches it for brackets, clamps, mechanical bits and printer parts, citing impact resistance plus water and chemical resistance. It also claims high transparency, so this green should print as a see-through tint rather than a solid color. Diameter tolerance is ±0.02mm, and each roll is dried for a day before vacuum packing, with filament clips in the box. What is missing is any temperature or speed guidance. This summary reflects the listing only.
What stands out
- 1.1kg on a reusable spool
- ±0.02mm diameter tolerance
- Translucent green tint
- Water and chemical resistant
Who it fits
Good fit for
Budget-minded makers printing practical PETG parts, from brackets to planters, who like a translucent colored look and a bit of extra filament per roll.
Who should skip it
Printers that need an opaque green should pick a solid-color PETG. If you want listed temperature and speed settings, JAYO does not provide them on this page.
Verdict: Low-cost, generous PETG with a translucent finish and no settings guide.
JAYO PETG specs decoded
1.1kg net
About 10% more prints per roll than a 1kg spool, per JAYO.
±0.02mm
A tight tolerance for steady extrusion and fewer under-extrusion gaps.
High transparency
Thin walls let light through, good for lamp shades and display pieces.
Impact and water resistance
Tougher than PLA for outdoor or wet-area parts.
What JAYO does not say
The listing gives no nozzle or bed temperature, no speed range and no recommended cooling. It describes PETG as combining PLA and ABS properties without numbers. The spec weight of 2.43 lb matches the 1.1kg net filament. Color is listed only as green, with no indication of how saturated the tint is.
Printing green PETG
PETG likes a slightly hotter nozzle and less part cooling than PLA, so start with your printer's PETG profile and tune from there. Use a glue stick or textured sheet if it bonds too hard to smooth PEI. Translucent filament shows infill, so pick the pattern with that in mind.
Before ordering
Two minutes of checks.
Check before you buy
- Your spool holder fits a 1.1kg roll
- Translucent green suits the job
- You have a working PETG profile
- You want PETG over PLA toughness
The product at a glance
JAYO PETG 1.75mm 1.1kg Green
Best for: Budget PETG with a tinted look
- Material Type
- PETG
- Filament Diameter
- 1.75mm
- Net Weight
- 1.1kg
- Dimensional Accuracy
- +/- 0.02 mm
- Printing Technology
- FDM
- Weight
- 2.43 pounds
View on Amazon: JAYO PETG 1.75mm 1.1kg Green Affiliate link
JAYO green PETG, 1.75mm on a 1.1kg reusable spool, ±0.02mm, pre-dried and vacuum sealed, with a translucent finish.
Pros
- Extra 100g per roll
- Tight tolerance
- Impact and water resistant
Cons
- No print settings given
- Translucent, not opaque
- Green only on this listing
Good fit if
- You print outdoor clips or brackets
- You want a cheap PETG restock
Skip if
- You need solid opaque color
- You want vendor print settings
Verdict: Cheap translucent PETG with extra filament.
Specifications side by side
| Spec | JAYO PETG 1.75mm 1.1kg Green |
|---|---|
| Material Type | PETG |
| Filament Diameter | 1.75mm |
| Net Weight | 1.1kg |
| Dimensional Accuracy | +/- 0.02 mm |
| Printing Technology | FDM |
| Compatible Material | PETG |
| Weight | 2.43 pounds |
| Color | 1.1kg Green |
Frequently asked questions
How much filament is on the JAYO green PETG spool?
1.1kg net, 100g more than a standard 1kg roll.
Is JAYO green PETG see-through?
JAYO advertises high transparency, so expect a translucent tint.
What temperature does JAYO PETG need?
The listing does not say; start from a typical PETG profile.
Does JAYO dry its PETG before packing?
Yes, JAYO says every roll gets a full day of drying before it is sealed.
