FauxHammer WARGAMER Resin 5 x 1kg Grey Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
WARGAMER is the miniature resin from FauxHammer, the wargaming channel, sold under the Yes, That's 3D Printed brand, and this pack holds five 1kg bottles of the grey V2 formula. FauxHammer's pitch is that prints should behave like injection-molded plastic minis: tough and slightly flexible so they survive games, and soft enough to scrape, shave and cut for kitbashing or cleaning up support marks. Two claims stand out against typical tough resins. It aims to stay sharp, without the slightly soft look ABS-like blends can give, and it can be washed in water or IPA without turning brittle the way many water-washable resins do. It cures glossy, like traditional plastic pieces, and FauxHammer says it keeps its strength over months rather than going brittle. The pack is rated at roughly 400 minis at 32mm scale. There are no exposure times, wavelength or hardness numbers on the page. This review reflects the FauxHammer listing.
What stands out
- Tough and flexible like plastic minis
- Cuts and shaves for kitbashing
- Washes in water or IPA
- Five 1kg grey bottles, about 400 minis at 32mm
Who it fits
Good fit for
Wargamers printing whole armies who want minis that handle like plastic kits and want the choice of water or IPA cleanup.
Who should skip it
Anyone who wants a matte surface, a single bottle to test first, or a listing with exposure settings.
Verdict: A wargaming-first resin with a clear goal; the 5kg pack makes sense once the 1kg bottle has proven itself on your printer.
WARGAMER 5 x 1kg, in plain terms
Tough, flexible, long-term stable
Minis survive drops and stay strong over months.
Scrape, shave and cut
Kitbash parts and clean support marks like plastic minis.
Water or IPA wash
Choose the cleanup that suits your setup.
Glossy grey finish
Shows detail and photographs well before painting.
5 x 1kg, about 400 minis at 32mm
Army-sized supply in separate bottles.
How WARGAMER differs from tough or ABS-like resins
Tough resins often sacrifice edge sharpness and come out slightly rubbery; WARGAMER claims to keep fine detail while staying flexible. The cut-and-shave behavior is the practical gain for hobbyists who convert models. Gloss is a deliberate choice: it mirrors plastic kits, though a matte resin hides layer lines a little better before priming. Five separate bottles keep the unopened ones sealed until needed.
Printing and washing WARGAMER
Start from a standard tough-resin profile for your printer and dial in with a test figure, since no settings are listed. Pick one wash method and stick to it; if you use water, let the waste water cure in sunlight and filter it before disposal. Prime glossy prints after a light scuff or with a primer that grips smooth surfaces.
Before ordering the WARGAMER 5-pack
A quick check for this FauxHammer pack.
Check before you buy
- You print enough minis to use 5kg of WARGAMER resin
- You are fine with a glossy WARGAMER finish
- You can set WARGAMER exposure without listed values
The product at a glance
WARGAMER Grey Miniature Resin 5 x 1kg
Best for: Wargame armies and kitbashing
- Resin Type
- Water-Washable
- Net Weight
- 5kg
- Cleaning Method
- Water or IPA
- Application
- Miniatures
- Printing Technology
- Resin
- Color
- Grey
View on Amazon: WARGAMER Grey Miniature Resin 5 x 1kg Affiliate link
WARGAMER by FauxHammer, five 1kg grey bottles: a tough, kitbash-friendly miniature resin with water or IPA cleanup.
Pros
- Handles like plastic kit minis
- Water or IPA wash
- Five sealed bottles
Cons
- No exposure or hardness data
- Glossy finish shows layer lines
- Large up-front buy
Good fit if
- You print armies
- You convert and kitbash minis
Skip if
- You want to test a single bottle first
Verdict: An army-sized supply of a wargaming-focused resin.
Specifications side by side
| Spec | WARGAMER Grey Miniature Resin 5 x 1kg |
|---|---|
| Resin Type | Water-Washable |
| Net Weight | 5kg |
| Cleaning Method | Water or IPA |
| Application | Miniatures |
| Printing Technology | Resin |
| Color | Grey |
| Size | 1KG |
| Dimensions | 9.25 × 4 × 4 inches |
| Weight | 11 pounds |
| Model | WARGAMER-5KGS-GREY-V2 |
Frequently asked questions
Does FauxHammer WARGAMER rinse clean in plain water?
Yes, FauxHammer says it washes in water or IPA.
How many minis does the WARGAMER 5kg pack make?
FauxHammer estimates about 400 minis at 32mm scale.
Is WARGAMER resin matte or glossy?
Glossy, like traditional plastic wargaming pieces.
Can WARGAMER prints be kitbashed?
Yes, prints can be scraped, shaved or cut like regular plastic minis.
Featured in
See also
- anycubic kobra x combo multi color 3d printer review
- anycubic photon p1 max black resin printer review
- anycubic photon p1 14k dual kit white review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- phrozen sonic mega 8k s resin 3d printer review
- zwilling henckels professional s review
