As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

EONO3D 95A TPU Filament (Blue, 1.75mm, 1kg) Review

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

EONO3D's 95A TPU in blue is a 1kg spool of 1.75mm flexible filament with Shore 95A hardness, which EONO3D compares to a shoe sole: firm, but it bends and compresses without cracking. The listing gives complete settings, 220-240°C at the nozzle, 50-60°C on the bed and 30-60mm/s, and says it works with both direct drive and Bowden extruders. Blue is the reason to pick this spool over black: EONO3D pitches it for drone parts, gaming accessories, phone cases and cosplay props, and for color-coding flexible parts such as cable sleeves, bumpers or feet so they are easy to tell apart. The spool comes vacuum sealed with desiccant, and EONO3D notes that TPU absorbs moisture and suggests drying at 50°C before use if the spool has been open. There are no tensile or elongation figures and no diameter tolerance on the listing. Our view comes from EONO3D's listing and spec fields; we did not print the spool.

What stands out

  • TPU, Shore 95A, blue, 1kg
  • 1.75mm (no tolerance stated)
  • 220-240°C nozzle / 50-60°C bed
  • 30-60mm/s
  • Direct drive or Bowden; dry at 50°C

Who it fits

Good fit for

Makers printing flexible parts that should stand out or be color-coded: drone bumpers, phone cases, gaming grips, cable sleeves and props.

Who should skip it

Anyone who needs very soft rubber (85A and below), published strength data, or fast printing above 60mm/s.

Verdict: A blue 95A TPU with clear settings; slow to print, as TPU is, but easy to set up.

EONO3D blue TPU 95A specs

Shore 95A

Firm-flexible, like a shoe sole.

220-240°C / 50-60°C

Nozzle and bed range from EONO3D.

30-60mm/s

Slow speeds keep the flexible strand from buckling.

Direct drive or Bowden

Bowden works, but tune retraction carefully.

Dry at 50°C

EONO3D's drying advice for an opened spool.

What blue 95A TPU is good for

At 95A, prints flex and absorb knocks but hold their shape, which suits drone arm guards, phone and remote cases, grips, feet, gaskets and watch straps. A bright blue makes sense where parts should be seen or sorted: replacement bumpers for a blue drone, controller grips, cable ends coded by device, or props for a costume. For soft, squishy parts such as seals that must compress a lot, a lower Shore number is the better match.

Printing EONO3D blue TPU

Stay inside the 30-60mm/s window and start near 230°C. On a Bowden printer, cut retraction short and slow the feed so the strand does not coil inside the tube; a direct drive extruder makes this easier. If an opened spool has sat out, dry it at 50°C as EONO3D suggests before printing, since wet TPU strings and bubbles. A PEI or textured plate at 50-60°C usually holds TPU well; use a release agent if parts stick too firmly.

Before buying EONO3D blue TPU

Checks.

Check before you buy

  • Your EONO3D TPU parts need flex at Shore 95A
  • You can print EONO3D TPU at 30-60mm/s
  • You want blue for color-coded flexible parts
  • You can dry an opened EONO3D spool at 50°C

The product at a glance

EONO3D 95A Blue TPU Filament

Best for: Color-coded flexible parts

Material Type
TPU
Filament Diameter
1.75mm
Net Weight
1kg
Shore Hardness
95A
Printing Technology
FDM
Color
Blue

View on Amazon: EONO3D 95A Blue TPU Filament Affiliate link

EONO3D blue TPU 95A 1kg: 220-240°C nozzle, 50-60°C bed, 30-60mm/s, direct drive or Bowden, vacuum sealed; no tolerance listed.

Pros

  • Full print settings listed
  • Works with Bowden as well as direct drive
  • Bright blue for color-coded parts

Cons

  • Slow 30-60mm/s printing
  • No diameter tolerance given
  • No strength figures

Good fit if

  • You print blue flexible bumpers or cases

Skip if

  • You need softer than 95A TPU

Verdict: A blue 95A TPU with clear settings for flexible parts.

Specifications side by side

Spec EONO3D 95A Blue TPU Filament
Material Type TPU
Filament Diameter 1.75mm
Net Weight 1kg
Shore Hardness 95A
Printing Technology FDM
Compatible Material TPU
Color Blue
Weight 2.2 pounds
Size 95A TPU

Frequently asked questions

What hardness is EONO3D blue TPU?

Shore 95A, firm but flexible.

What temperatures does EONO3D list for its blue 95A TPU?

220-240°C at the nozzle and 50-60°C on the bed.

How fast can EONO3D blue TPU print?

EONO3D recommends 30-60mm/s.

Does EONO3D blue TPU work on Bowden printers?

EONO3D says it works with direct drive and Bowden extruders; Bowden needs careful retraction tuning.

Should EONO3D blue TPU be dried?

EONO3D notes TPU absorbs moisture and suggests drying at 50°C before use.

See also