UniTak3D Photon Mono 2/Mono 4 FEP Film Review: Who It Fits and Who Should Skip It
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
UniTak3D sells this pack of two replacement FEP sheets for Anycubic's Photon Mono 2 and Mono 4 10K resin printers. Each 197×131mm film comes already bonded to a steel ring, so a worn vat bottom can be swapped without cutting or stretching loose film. The seller quotes over 95% light transmittance, 204°C heat resistance and more than 30,000 releases per sheet. A spare pair costs under $20, which makes it an easy item to keep in the drawer. Despite the word "Original" in the listing title, the brand is UniTak3D, not Anycubic. We have not installed these sheets; everything here is drawn from the product page.
What stands out
- Two framed sheets per pack
- Steel ring, no cutting needed
- Sized 197×131mm for Mono 2 and Mono 4 10K
- Over 95% light transmittance claimed
Who it fits
Good fit for
Photon Mono 2 or Mono 4 10K owners whose vat film is scratched, cloudy or punctured, and anyone who wants a spare on hand before a long resin job.
Who should skip it
Owners of other resin machines, including the larger Mono X or Mono M series, should look elsewhere, since only these two Anycubic models appear on the page. It is also just the film, so a cracked or warped vat frame still needs a full vat.
Verdict: A low-cost, pre-framed FEP two-pack that turns a Mono 2 or Mono 4 film change into a quick job.
FEP film specs explained
197×131mm with steel ring
The film arrives tensioned on a frame that matches the Mono 2/Mono 4 vat, so there is no trimming or screw-by-screw stretching.
Over 95% light transmittance
Clear film lets the UV screen cure each layer evenly; cloudy old film is a common cause of soft or failed layers.
204°C heat resistance
Far above what a resin vat sees, so heat is not the limiting factor; scratches and punctures are.
0.15 thickness, 2 pieces
The title lists 0.15 thickness without a unit; 0.15mm is a common FEP gauge, and you get two sheets per order.
Listing notes
The product page calls the film chemically resistant and non-stick, with peeling performance that meets FEP release needs, but it gives no test data behind the 30,000-release figure. It also leaves out the thickness unit and does not say whether screws or gaskets are included. The word "Original" sits in the listing title even though UniTak3D is the seller brand, so treat these as aftermarket replacements built to the Anycubic size.
Swapping the film
Empty and clean the vat first, then remove the old framed film from the vat body and seat the new ring in its place. Check for leaks with a little isopropyl alcohol before pouring resin back in. Wipe the film only with soft tools, because a scratched surface can print streaks or tear under peel forces, and keep the second sheet sealed until it is needed.
Before ordering
Quick checks.
Check before you buy
- Your printer is a Photon Mono 2 or Mono 4 10K
- Only the film is worn, not the vat frame
- You are fine with an aftermarket sheet
- You have a plastic scraper for cleaning
The product at a glance
UniTak3D 197 x 131mm Steel Ring FEP Film
Best for: Photon Mono 2 / Mono 4 10K film replacement
- Dimensions
- 197 * 131mm
- Maximum Temperature
- 204 ℃
- Release Film Type
- FEP
- Printing Technology
- Resin
View on Amazon: UniTak3D 197 x 131mm Steel Ring FEP Film Affiliate link
A UniTak3D two-pack of 197×131mm FEP films on steel rings for the Photon Mono 2 and Mono 4 10K, rated over 95% clarity and 204°C.
Pros
- Two framed sheets per order
- No cutting or stretching
- Cheap spare to keep around
Cons
- Fits two Anycubic models only
- Thickness unit not stated
- No test data behind release count
Good fit if
- Your Mono 2 film is scratched or cloudy
- You want a spare Mono 4 10K sheet ready
Skip if
- You own a Mono X or another vat size
- The vat frame itself is damaged
Verdict: An easy, inexpensive film refresh for Photon Mono 2 and Mono 4 owners.
Specifications side by side
| Spec | UniTak3D 197 x 131mm Steel Ring FEP Film |
|---|---|
| Dimensions | 197 * 131mm |
| Maximum Temperature | 204 ℃ |
| Release Film Type | FEP |
| Printing Technology | Resin |
Frequently asked questions
Which printers does the UniTak3D 197×131mm FEP fit?
The listing names Anycubic's Photon Mono 2 and Photon Mono 4 10K only.
How many sheets come in this UniTak3D order?
Two, each already mounted on its steel ring.
Is it made by Anycubic?
No. The title says "Original" but the seller brand is UniTak3D; it is a replacement built to the Anycubic size.
Do I need to cut the UniTak3D film to size?
No, the sheet is integrated with its ring, so it drops into the vat without trimming.
