Voxelab PLA Pro (PLA+) Filament Review: Specs, Pros and Cons
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Voxelab's PLA Pro is a 1kg spool of black 1.75mm PLA+ sold for under $20, aimed at everyday FDM printing on almost any machine. Its listing gives more practical numbers than many budget spools: a ±0.02mm diameter tolerance, a 190-220°C nozzle range, a 25-60°C bed range and full spool dimensions. It ships vacuum sealed with a desiccant pack. What the page does not give is any strength figure, so the "Pro" label is a claim rather than a measured gain over plain PLA. We have not printed with this spool; the notes below come from Voxelab's own product text.
What stands out
- ±0.02mm diameter tolerance
- Clear temperature ranges for nozzle and bed
- Vacuum sealed with desiccant
- Full spool dimensions published
Who it fits
Good fit for
Beginners and hobbyists who want a cheap, low-warp black filament for figures, brackets and test prints, and owners of an AMS or holder who need to know the spool size before buying.
Who should skip it
If you need proven toughness for load-bearing parts, a filament with published tensile or impact data serves you better. Heat-exposed parts, such as anything left in a car, call for PETG or ASA instead.
Verdict: A well-documented budget PLA+ spool for general printing, with the strength upgrade left unproven.
PLA Pro specs explained
1.75mm ±0.02mm
A tight diameter keeps flow steady, which helps avoid under-extruded gaps and blobs.
Nozzle 190-220°C, bed 25-60°C
Standard PLA settings; a bed around 50-60°C suits most textured or PEI plates.
Spool 200mm flange, 53mm hub, 65mm wide
Lets you confirm it fits your holder or multi-material unit before ordering.
Vacuum packed with desiccant
Arrives dry; reseal it after opening because damp PLA turns brittle and can jam.
Listing notes
Voxelab describes this spool as clog-free, bubble-free and tangle-free, with minimal shrinkage, but gives no figures for strength or layer bonding, the usual reasons to pick PLA+ over standard PLA. The spec field "size" simply repeats "PLA PRO", and the color is black on this listing. No print speed range is listed, so high-speed printers will need their own tuning.
Printing with it
Start in the middle of the range, around 205-210°C, and adjust by a few degrees if layers look rough or stringy. A clean bed at 50-60°C is usually enough for adhesion on PLA. Store the opened spool in a sealed bag or dry box between jobs, as the page itself advises.
Before ordering
Quick checks.
Check before you buy
- Your printer takes 1.75mm filament
- A 200mm spool fits your holder or AMS
- Black is the color you need
- Parts will not sit in high heat
The product at a glance
Voxelab PLA Pro 1.75mm Filament
Best for: Everyday black PLA+ printing on a budget
- Material Type
- PLA Pro (PLA+)
- Filament Diameter
- 1.75mm
- Net Weight
- 1kg
- Dimensional Accuracy
- +/- 0.02 mm
- Printing Technology
- FDM
- Color
- Black
View on Amazon: Voxelab PLA Pro 1.75mm Filament Affiliate link
Voxelab's black 1kg PLA Pro spool: 1.75mm ±0.02mm, 190-220°C nozzle, 25-60°C bed, vacuum packed, with published spool dimensions.
Pros
- Cheap 1kg spool
- Tight diameter tolerance
- Clear print settings and spool size
Cons
- No strength data for the PLA+ claim
- No speed range given
- PLA heat limits
Good fit if
- You want low-cost black PLA+ for general prints
- You need spool dimensions to check holder fit
Skip if
- You need documented toughness
- Your parts face heat or sun
Verdict: A dependable-looking budget black PLA+ with honest settings and unproven extra strength.
Specifications side by side
| Spec | Voxelab PLA Pro 1.75mm Filament |
|---|---|
| Material Type | PLA Pro (PLA+) |
| Filament Diameter | 1.75mm |
| Net Weight | 1kg |
| Dimensional Accuracy | +/- 0.02 mm |
| Printing Technology | FDM |
| Compatible Material | PLA |
| Color | Black |
| Dimensions | 7.87 × 7.87 × 2.56 inches |
| Weight | 2.2 pounds |
| Size | PLA PRO |
| Model | PLA PRO |
Frequently asked questions
What temperature does Voxelab PLA Pro print at?
Voxelab gives 190-220°C at the nozzle and 25-60°C for the bed.
Is Voxelab PLA Pro stronger than regular PLA?
The listing calls it PLA+ but publishes no strength numbers, so the gain cannot be checked from the page.
Will this Voxelab spool fit a Bambu AMS?
The listed 200mm flange, 53mm hub and 65mm width are common sizes; compare them with your AMS limits before buying.
Does Voxelab PLA Pro come dried?
It is vacuum sealed with desiccant, so it should arrive ready to print.
Featured in
See also
- prusament woodfill pastel brown 1 75mm review
- yousu 3d printer filament review
- yousu silk pla filament 1 75mm review
- voxelab burnt titanium chameleon pla review
- voxelab luminous hs glow pla filament review
- VOXELAB Silk+ PLA (Blue, 1kg) Review
- geeetech 3d printer kids review
- unxuey 50pcs 3d printer heatsink review
