SUNLU PA6-GF25 Glass Fiber Nylon Filament Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
SUNLU PA6-GF is a 25% glass fiber, 75% nylon 6 filament for stiff, heat-resistant functional parts such as brackets, housings, jigs and drone motor mounts. Its headline is a 205°C (401°F) heat rating, which SUNLU says the material withstands while keeping strength and stiffness; the listing does not say which test that figure comes from, so treat it as a maximum service claim. Settings are demanding: 270-290°C nozzle, 50-70°C bed with glue, 50-120mm/s. Glass fiber wears brass and copper nozzles, so SUNLU asks for a hardened steel nozzle, and it advises against AMS, AMS Lite and other multi-color feeders to avoid breakage. Moisture is the other hurdle: after six hours out of the bag it needs drying at 110°C for 4 hours, and the spool itself is heat-resistant so it can go straight into a dryer. SUNLU also claims chemical resistance to acids, fuels and cleaners. This review summarizes the SUNLU listing; we have not printed it.
What stands out
- 25% glass fiber, 75% PA6
- 270-290°C nozzle, 50-70°C bed, 50-120mm/s
- 205°C heat rating (test not named)
- Dry 110°C for 4h; spool survives 110°C
- Hardened nozzle; no AMS
Who it fits
Good fit for
Engineers and advanced hobbyists with a hardened nozzle, a 290°C hotend and a hot dryer who need rigid, heat- and chemical-resistant parts.
Who should skip it
Anyone on a stock brass nozzle, a PTFE-lined hotend, or a multi-color feeder, and beginners who want an easy nylon.
Verdict: A capable industrial nylon if your printer and dryer meet SUNLU's requirements.
SUNLU PA6-GF25 numbers explained
25% glass fiber
Stiffer and more stable than plain nylon, but abrasive.
270-290°C nozzle
Needs an all-metal hotend rated near 300°C.
50-70°C bed + glue
SUNLU recommends glue against edge warping.
205°C heat rating
SUNLU's maximum heat claim; no test method given.
110°C for 4h drying
Required if the spool has been open 6 hours.
What glass fiber adds
Glass fiber stiffens nylon and cuts warping, which SUNLU backs with claims of low warpage, high dimensional accuracy and a smooth surface. The fibers also make the filament brittle in tight paths and abrasive to soft nozzles, which is why SUNLU rules out AMS-type feeders and copper nozzles. Gray color is listed as hex #6e7174.
Printing SUNLU PA6-GF in practice
Dry the spool at 110°C for 4 hours before every session that follows more than six hours of exposure, then feed it directly from a dry box. Fit a hardened steel nozzle, print at 270-290°C with a 50-70°C bed and glue, and keep speeds within 50-120mm/s. Large flat parts benefit from a brim, in line with SUNLU's warning about edge warping.
Before buying SUNLU PA6-GF25
Checks.
Check before you buy
- Your printer has a hardened nozzle for SUNLU PA6-GF
- Your hotend handles 290°C for SUNLU glass fiber nylon
- Your dryer reaches 110°C for SUNLU PA6-GF
The product at a glance
SUNLU PA6-GF 25% Glass Fiber Nylon
Best for: Heat-resistant rigid parts
- Material Type
- PA6-GF
- Filament Diameter
- 1.75mm
- Net Weight
- 1KG
- Max Print Speed
- 120mm/s
- Compatible Material
- Nylon
- Dimensions
- 7.87 × 2.76 × 7.87 inches
View on Amazon: SUNLU PA6-GF 25% Glass Fiber Nylon Affiliate link
SUNLU PA6-GF25 gray 1kg: 25% glass fiber nylon 6, 270-290°C, bed 50-70°C with glue, 50-120mm/s, 205°C heat claim, dry 110°C 4h, hardened nozzle, no AMS.
Pros
- Rigid and heat resistant
- Chemical resistance claims
- Dryer-safe spool
Cons
- Hardened nozzle required
- Not for AMS feeders
- Needs drying after 6h exposure
Good fit if
- You make heat-exposed jigs, brackets or housings
Skip if
- You print from an AMS or with a brass nozzle
Verdict: Strong industrial nylon for well-equipped printers.
Specifications side by side
| Spec | SUNLU PA6-GF 25% Glass Fiber Nylon |
|---|---|
| Material Type | PA6-GF |
| Filament Diameter | 1.75mm |
| Net Weight | 1KG |
| Max Print Speed | 120mm/s |
| Compatible Material | Nylon |
| Dimensions | 7.87 × 2.76 × 7.87 inches |
| Weight | 2.2 pounds |
| Size | Nylon |
| Color | 1kg Pa6-gf25 Grey (Hex Code: #6e7174) |
| Model | Filament Technique d'Impression 3D |
Frequently asked questions
How much glass fiber is in SUNLU PA6-GF?
25% glass fiber and 75% PA nylon.
What temperatures does SUNLU list for PA6-GF?
270-290°C nozzle, 50-70°C bed, 50-120mm/s.
Can SUNLU PA6-GF run in a Bambu AMS?
SUNLU says no; it is not recommended for AMS, AMS Lite or other multi-color systems.
How do you dry SUNLU PA6-GF?
110°C for 4 hours, needed once the spool has been open six hours.
Does SUNLU PA6-GF need a special nozzle?
Yes, a wear-resistant nozzle such as hardened steel.
See also
- sunlu fast curing standard resin clear 1kg review
- sunlu high speed abs filament 2 pack black review
- amolen silk rainbow pla orange yellow blue pink review
- sunlu pla filament review
- sunlu pla plus 2 0 filament review
- SUNLU PLA Plus Filament 1.75mm Review: Who It Fits and Who Should Skip It
- SUNLU 1kg Transparent PETG Filament Review (2026): A Spec-Based Look
- SUNLU 1KG Wood Fiber PLA Review: Specs, Pros and Cons
- kingcamp fiber glass folding camping review
- astralship glass blenders review
