As an Amazon Associate we earn from qualifying purchases. Affiliate disclosure

Siraya Tech Fibreheart PPA Filament (Black, 1kg) Review

Latest update:

As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.

Siraya Tech Fibreheart PPA is a 1kg spool of black polyphthalamide, a high-temperature nylon, and it is meant for parts that wear: gears, bushings, bearings and brackets that sit near heat or oil. The main reason to pick it over plain nylon is moisture. Siraya Tech says it soaks up about one fifth of the water PA6 takes at saturation, with a listed 2.50% absorption, so it should hold its size better between drying runs. Listed strength is 70 MPa tensile and 114 MPa flexural, both measured dry, at a density of 1.2 g/cm³. The listing also calls it PAHT in one bullet, so the two names refer to the same spool. What it does not give is a nozzle temperature, a bed temperature, a speed range or a heat deflection figure, so plan on a high-temperature hotend and your own test prints. We read Siraya Tech's product page and spec fields for this; nothing here comes from a printer of ours.

What stands out

  • Polyphthalamide (PPA), 1kg black
  • 70 MPa tensile, 114 MPa flexural (dry)
  • 2.50% water absorption
  • Self-lubricating, low friction
  • No print temperatures listed

Who it fits

Good fit for

Engineers and hobbyists printing gears, bushings and jigs that rub, carry load or sit near heat and chemicals.

Who should skip it

Anyone on a stock PTFE-lined hotend, or anyone who wants a filament with settings printed on the box.

Verdict: A wear-resistant engineering nylon with real strength data but no print profile, best for tuned high-temperature printers.

Fibreheart PPA numbers from the listing

70 MPa tensile (dry)

Siraya Tech says this beats common nylons; wet parts will be weaker.

114 MPa flexural (dry)

Stiffness for brackets and arms under bending load.

2.50% water absorption

About one fifth of PA6 at saturation, per the listing.

1.2 g/cm³ density

A 1kg spool gives a little less length than PLA at 1.24.

Self-lubricating surface

Aimed at gears and bearings that run without grease.

What PPA brings over standard nylon

PPA is a semi-aromatic polyamide, so Siraya Tech pitches it for automotive, aerospace and factory parts that meet heat and aggressive chemicals. The low friction claim is the practical draw: printed gears and slide bushings wear in rather than chewing themselves up. The listing gives no carbon or glass fill, which makes this an unfilled grade, unlike the PPA-CF spools that need hardened nozzles for abrasion.

Printing Fibreheart PPA without a stated profile

Because Siraya Tech lists no temperatures, start from your slicer's PPA or high-temperature nylon preset and print a temperature tower first. Expect to need an all-metal hotend and an enclosure to limit warping. Even with lower water uptake, dry the spool before use and keep it sealed with desiccant, as the listing itself advises proper drying and storage.

Before ordering Fibreheart PPA

Checks.

Check before you buy

  • Your hotend is all-metal for Fibreheart PPA temperatures
  • You can enclose the printer to keep PPA parts flat
  • You have a dryer or sealed box for the PPA spool
  • You will tune PPA settings yourself

The product at a glance

Siraya Tech Fibreheart PPA 1.75mm

Best for: Wear-resistant gears

Material Type
PPA
Filament Diameter
1.75mm
Net Weight
1kg
Compatible Material
Nylon
Dimensions
3.94 × 8.66 × 8.66 inches
Weight
2.2 pounds

View on Amazon: Siraya Tech Fibreheart PPA 1.75mm Affiliate link

Siraya Tech Fibreheart PPA 1kg black: unfilled polyphthalamide, 70 MPa tensile and 114 MPa flexural dry, 2.50% water uptake, self-lubricating for gears; no print settings listed.

Pros

  • Dry strength figures published
  • Lower moisture uptake than PA6
  • Low friction for gears and bushings

Cons

  • No nozzle or bed temperature given
  • Needs an all-metal hotend
  • Still needs drying and sealed storage

Good fit if

  • You print load-bearing Fibreheart PPA gears or bushings

Skip if

  • You want a Fibreheart PPA spool with settings on the label

Verdict: An engineering PPA for wear parts on a tuned, enclosed printer.

Specifications side by side

Spec Siraya Tech Fibreheart PPA 1.75mm
Material Type PPA
Filament Diameter 1.75mm
Net Weight 1kg
Compatible Material Nylon
Size 1.75Mm
Dimensions 3.94 × 8.66 × 8.66 inches
Weight 2.2 pounds
Color Ppa Black 1kg

Frequently asked questions

What print temperature does Siraya Tech Fibreheart PPA need?

Siraya Tech gives no PPA temperature. Start from a PPA or high-temperature nylon profile and run a temperature tower.

How strong is Fibreheart PPA?

Siraya Tech lists 70 MPa tensile and 114 MPa flexural strength, both dry.

Does Fibreheart PPA absorb moisture like nylon?

Less: the listing gives 2.50% water absorption, about one fifth of PA6 at saturation, but it still advises drying.

Is Fibreheart PPA the same as PAHT?

The listing uses both names for this spool; PAHT is a common label for high-temperature polyamide.

Does Fibreheart PPA contain carbon fiber?

No fill is listed for this black PPA, unlike PPA-CF grades.

See also