MORKEYA Photon Mono M7 Magnetic Build Plate (228x131mm) Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
MORKEYA's magnetic build plate is a two-part kit for the Anycubic Photon Mono M7 and M7 Pro: a magnetic base that sits on the printer's build platform and a 228×131mm flexible spring steel plate that clamps onto it. The reason resin users buy one is removal. Instead of chiselling parts off a rigid aluminum platform with a scraper, you lift the steel sheet off and flex it, and prints pop free with less risk of snapping thin parts or gouging the plate. The surface is described two ways: the title says textured, the bullets say a precision brushed finish for first-layer grip, so expect a fine texture rather than a coarse one. MORKEYA says the sheet cleans with water or a soft cloth, though resin users will normally use isopropyl alcohol. The listing does not say how the base attaches to the M7 platform or how much the kit adds to plate thickness, and the spec dimensions (0.79in on every side) are clearly placeholders. These notes come from MORKEYA's listing only; we have not fitted the plate.
What stands out
- Fits Photon Mono M7 / M7 Pro
- 228×131mm spring steel sheet
- Magnetic base included
- Brushed (title: textured) surface
- Attachment and added height not stated
Who it fits
Good fit for
Photon Mono M7 and M7 Pro owners who print delicate minis or many small parts and want to flex prints off instead of scraping.
Who should skip it
Owners of other printers (MORKEYA sells other sizes), and anyone who does not want to re-level and re-set Z after adding a magnetic layer.
Verdict: A practical removal upgrade for the M7 and M7 Pro; plan on re-leveling after fitting.
MORKEYA M7 plate specs
228×131mm
Cut for the Photon Mono M7 and M7 Pro.
Spring steel sheet
Flexes to release cured parts.
Magnetic base
Holds the sheet in place during printing.
Brushed / textured face
Grip for the first resin layers.
Fixing method not stated
Check how the base attaches to the M7 platform.
Why a flex plate helps on the M7
Resin prints bond hard to the platform, especially the rafts of large or flat parts. Scraping them off takes force, and the scraper can slip into thin supports or chip the model. With a spring steel sheet you remove the sheet, bend it slightly, and the raft peels away. It also speeds up batches: one sheet can go to the wash station while the printer is cleaned and restarted.
Fitting the MORKEYA plate to an M7
Clean the original platform, attach the magnetic base as the instructions say, and place the steel sheet so its edges line up with the platform. The extra layers raise the build surface, so re-level the platform and set Z-zero again before the first print. Wipe resin off the sheet with isopropyl alcohol, and keep the magnetic base clean and dry so the sheet sits flat.
Before buying the MORKEYA M7 plate
Checks.
Check before you buy
- You own an M7 or M7 Pro for the MORKEYA plate
- You will re-level the M7 after fitting the MORKEYA base
- You want to flex resin parts off the M7 plate
- You accept the unstated MORKEYA fixing method
The product at a glance
MORKEYA 228x131mm Magnetic Build Plate
Best for: Photon Mono M7 owners
- Primary Material
- Spring steel
- Dimensions
- 228x131mm
- Build Surface Type
- Brushed
- Surface Finish
- Textured
View on Amazon: MORKEYA 228x131mm Magnetic Build Plate Affiliate link
MORKEYA 228×131mm magnetic spring steel plate for Photon Mono M7/M7 Pro: flex to release prints; brushed vs textured wording, fixing method not stated.
Pros
- Flex-off print removal
- Cut for M7 and M7 Pro
- Magnetic base included
Cons
- Fixing method not explained
- Re-leveling needed
- Surface described two ways
Good fit if
- You print many small resin parts on an M7
Skip if
- You do not want to re-level
Verdict: A flex plate upgrade for the Photon Mono M7.
Specifications side by side
| Spec | MORKEYA 228x131mm Magnetic Build Plate |
|---|---|
| Primary Material | Spring steel |
| Dimensions | 228x131mm |
| Build Surface Type | Brushed |
| Build Plate Material | Spring Steel |
| Surface Finish | Textured |
| Size | 228x131mm(9x*5.2in) |
Frequently asked questions
Which printers does the MORKEYA 228x131mm plate fit?
The Anycubic Photon Mono M7 and M7 Pro.
Is the MORKEYA M7 plate textured or brushed?
The title says textured; the bullets describe a brushed finish.
Does the MORKEYA M7 plate need re-leveling?
Expect to re-level and reset Z, since the base and sheet add height.
How do you remove resin prints from the MORKEYA M7 sheet?
Lift the spring steel sheet off the magnetic base and flex it.
How do you clean the MORKEYA M7 sheet?
MORKEYA mentions water or a soft cloth; resin users usually wipe with isopropyl alcohol.
See also
- hysiprui flashforge creator 5 cool build plate review
- elegoo abs like ultra resin neon lemon 2kg review
- sunlu water washable resin dark grey 4kg review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- vevor magnetic drill review
- cusimax hot plate review
