HysiPrui FLASHFORGE Creator 5 Cool Build Plate (Purple) Review
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
HysiPrui's purple cool plate is a double-sided smooth spring steel sheet for the FLASHFORGE Creator 5 and Creator 5 Pro. A cool plate is built to hold PLA at low or no bed heat, and HysiPrui says it can print cold, without glue. The bullets then give bed ranges, 30-50°C for PLA and 50-70°C for PETG, so read "no heating" as "low heat" and use those numbers. HysiPrui is clear that the plate is for PLA and PETG only, so ABS, ASA, nylon and TPU belong on a textured PEI sheet. The case for it on a Creator 5 is long multi-color PLA jobs: a lower bed temperature cuts heat-up time and energy use, and both faces can be used, so one side can wear while the other stays fresh. A slight bend of the HysiPrui sheet releases finished parts. The listing gives no coating name beyond smooth PEI, no thickness and no number of print cycles. Our review relies on HysiPrui's listing and spec fields; we have not printed on the plate.
What stands out
- Fits FLASHFORGE Creator 5 / 5 Pro
- Double-sided smooth cool plate, purple
- PLA 30-50°C bed, PETG 50-70°C
- PLA and PETG only
- Flexible spring steel
Who it fits
Good fit for
Creator 5 and 5 Pro owners who print mostly PLA and some PETG and want low bed temperatures and a glossy underside.
Who should skip it
Anyone printing ABS, ASA, nylon or TPU, or who wants a textured bottom finish.
Verdict: A low-temperature PLA/PETG sheet for the Creator 5; keep a textured PEI plate for other materials.
HysiPrui Creator 5 cool plate specs
Cool plate, double-sided
Two smooth faces for low-temp printing.
PLA 30-50°C
HysiPrui's bed range for PLA.
PETG 50-70°C
HysiPrui's bed range for PETG.
PLA and PETG only
Other materials are not supported.
Spring steel
Flex the sheet to release prints.
Why a cool plate on the Creator 5
The Creator 5 is a four-toolhead multi-color printer, so it often runs long PLA jobs with many tool changes. A plate that holds PLA at 30-50°C reaches temperature faster and keeps the enclosure cooler, which PLA prefers. Smooth faces give a glossy bottom surface, useful for signs, coasters and flat-faced models. PETG can grip smooth surfaces very hard, so use the upper end of its range only as needed and consider a release layer.
Using the HysiPrui cool plate
Set the bed to the HysiPrui range for the material, clean the surface with isopropyl alcohol and avoid touching it with bare fingers. Let prints cool before flexing them off. If PETG bonds too strongly, a thin glue layer acts as a release rather than as an adhesive. Rotate between the two sides to spread the wear.
Before buying the HysiPrui Creator 5 cool plate
Checks.
Check before you buy
- Your printer is a FLASHFORGE Creator 5 or 5 Pro
- You print mostly PLA and PETG on the Creator 5
- You want a glossy bottom finish on Creator 5 prints
- You keep a textured plate for other Creator 5 materials
The product at a glance
HysiPrui Cool Build Plate for Flashforge Creator 5
Best for: Creator 5 PLA printing
- Maximum Temperature
- 70°C
- Build Surface Type
- Smooth
- Build Plate Material
- PEI, Spring Steel
View on Amazon: HysiPrui Cool Build Plate for Flashforge Creator 5 Affiliate link
HysiPrui purple cool plate for Creator 5/5 Pro: double-sided smooth spring steel, PLA 30-50°C and PETG 50-70°C bed, PLA/PETG only.
Pros
- Low bed temperatures for PLA
- Two usable smooth faces
- Flex-off removal
Cons
- PLA and PETG only
- "No heating" conflicts with bed ranges
- No thickness or coating details
Good fit if
- You print mostly PLA on a Creator 5
Skip if
- You print ABS or nylon
Verdict: A low-temp PLA/PETG plate for the Creator 5.
Specifications side by side
| Spec | HysiPrui Cool Build Plate for Flashforge Creator 5 |
|---|---|
| Maximum Temperature | 70°C |
| Build Surface Type | Smooth |
| Build Plate Material | PEI, Spring Steel |
| Surface Finish | Smooth |
| Color | Purple |
Frequently asked questions
Which printers does the HysiPrui cool plate fit?
Only FLASHFORGE's Creator 5 and its Pro version.
Can the HysiPrui Creator 5 cool plate print without heat?
HysiPrui says no heating is required, but lists 30-50°C for PLA and 50-70°C for PETG.
Which filaments work on the HysiPrui Creator 5 cool plate?
Only PLA and PETG, per HysiPrui.
Is the HysiPrui Creator 5 cool plate double-sided?
Yes, both sides are smooth and usable.
How do prints come off the HysiPrui Creator 5 cool plate?
Bend the spring steel sheet slightly; no tools needed.
See also
- elegoo abs like ultra resin neon lemon 2kg review
- sunlu water washable resin dark grey 4kg review
- inslogic flexible 70a resin black 1kg review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- cusimax hot plate review
- levoit smart cool mist top review
