Kingroon Silk PLA Red 1.75mm Filament Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Kingroon Silk PLA in red is a good choice for anyone who wants a glossy single-color spool with settings in the listing. Kingroon prints its numbers in the bullets: 220±10°C nozzle, 25-60°C bed, 40-80mm/s, plus a 1mm retraction at 20mm/s. Few silk spools include a datasheet like that, with 28.1 MPa tensile strength, 1.4% elongation at break and a 61°C glass transition. One point to note: the title says ±0.03mm while a bullet says ±0.02mm, so treat ±0.03mm as the safe figure. The spool is dried for 24 hours and vacuum sealed with desiccant.
What stands out
- Full print settings listed
- Tensile, bending and impact data
- Vacuum sealed with desiccant
Who it fits
Good fit for
Makers printing decor, cosplay props or gifts in a shiny red who like to start from the maker's own temperature, speed and retraction values.
Who should skip it
Anyone printing parts that flex or carry load (1.4% elongation means it snaps rather than bends), or who wants high-speed printing above 80mm/s.
Verdict: A red silk PLA with more published data than most; print it slowly for the best shine.
Kingroon red silk datasheet
Nozzle 220±10°C, bed 25-60°C
Listed starting window.
Speed 40-80mm/s
Slower than high-speed PLA.
Retraction 1mm at 20mm/s
Short retraction for direct drive or tuned setups.
Tensile 28.1±1.3 MPa (X-Y)
Fine for decor, not for brackets.
Elongation at break 1.4%
Brittle under bending.
Glass transition 61°C
Keep prints out of hot cars.
±0.03mm title / ±0.02mm bullet
The listing gives both.
Spool and finish
The spool is machine wound and checked by hand, and Kingroon says the inner diameter is larger for smoother feeding. Silk PLA gets its pearly shine from additives that reduce stiffness, which the bending modulus of 2119 MPa reflects. Red silk hides layer lines better than matte colors, so curved models look smooth.
Getting the shine
Print within the 40-80mm/s range and keep outer walls near the low end. Too hot and the gloss turns stringy; too cool and it looks dull. The listed density of 1.17-1.24 g/cm³ helps slicers estimate weight. Re-bag the spool with the desiccant after each session.
Before you buy
Checks for Kingroon red silk PLA.
Check before you buy
- You want a shiny single-color red
- You print at 80mm/s or slower
- You print decor rather than parts that flex
- You value listed retraction values
The product at a glance
Kingroon Silk PLA Red 1.75mm
Best for: Glossy red decor prints
- Material Type
- PLA
- Filament Diameter
- 1.75 mm
- Net Weight
- 1 kg
- Max Print Speed
- 80(mm/s)
- Dimensional Accuracy
- +/- 0.03 mm
- Surface Finish
- Silk
View on Amazon: Kingroon Silk PLA Red 1.75mm Affiliate link
Kingroon red silk PLA, 1kg 1.75mm: 220±10°C, 40-80mm/s, 1mm retraction, 28.1 MPa tensile, 61°C Tg; tolerance listed as both ±0.03 and ±0.02mm.
Pros
- Full datasheet in the listing
- Glossy red finish
- Vacuum sealed and dried
Cons
- Brittle (1.4% elongation)
- Max 80mm/s
Good fit if
- You want listed settings
- You print decor
Skip if
- You print flexing parts
Verdict: A shiny red PLA backed by real numbers.
Specifications side by side
| Spec | Kingroon Silk PLA Red 1.75mm |
|---|---|
| Material Type | PLA |
| Filament Diameter | 1.75 mm |
| Net Weight | 1 kg |
| Max Print Speed | 80(mm/s) |
| Dimensional Accuracy | +/- 0.03 mm |
| Surface Finish | Silk |
| Compatible Material | PLA |
| Color | Red |
| Finish | Silk |
| Dimensions | 8.19 × 2.72 × 8.4 inches |
| Weight | 2.2 pounds |
| Size | Silk PLA |
| Model | YMX0025 |
Frequently asked questions
What temperature does Kingroon list for silk PLA?
Nozzle 220±10°C and bed 25-60°C.
How fast can I print Kingroon silk PLA?
The listing gives 40-80mm/s.
Is Kingroon silk PLA ±0.02 or ±0.03mm?
The title says ±0.03mm and a bullet says ±0.02mm.
How heat resistant is it?
The listed glass transition is 61°C.
Kingroon red silk or a high-speed PLA?
Pick this silk for glossy decor at moderate speed; pick a high-speed PLA if print time matters more than shine.
