HICTOP GT2 Belt Clamps (10-Pack) Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
A loose or frayed belt end is a common reason for layer shift on budget printers, and the small copper buckle that holds the loop closed is easy to lose during a rebuild. HICTOP sells these GT2 belt clamps in a pack of 10. They are copper crimps for 6mm GT2 timing belts: feed the belt ends in and squeeze the clamp shut with pliers. HICTOP names the Creality Ender 3, Ender 5 and CR-10 as common uses, and any printer that closes a 6mm belt loop with a crimp will take them. The listing gives no clamp dimensions, no tooth spacing beyond the GT2 name and no 10mm version, so wider belts need a different part. This summary follows HICTOP's listing.
What stands out
- 10 copper clamps
- For 6mm GT2 belts
- Crimp with pliers
Who it fits
Good fit for
Owners of Ender 3, Ender 5 or CR-10 style printers replacing a belt or rebuilding an axis.
Who should skip it
Anyone with 9mm or 10mm belts, and printers that use screw-type belt holders instead of crimps.
Verdict: Cheap spare parts that are worth keeping in a drawer for belt jobs.
HICTOP GT2 clamp specs
10 pieces
Enough for several belt jobs.
Copper
Durable crimp metal.
6mm GT2 belts
Belt width.
Pliers to fit
No special tool.
Ender 3 / Ender 5 / CR-10
Named uses.
Clamp size
Not listed.
What the clamp does
On many Creality-style axes the belt runs around the pulley and idler and its two ends are held together by a copper buckle. If that buckle slips, belt tension drops and prints shift. A fresh crimp gives a firm loop again. Because each clamp is crimped once, keep spares: a mistake in belt length means cutting the clamp off and using a new one.
Fitting a belt with them
Cut the belt to length, overlap the teeth of the two ends inside the clamp, squeeze it flat with pliers and then tension the belt with the printer's tensioner. Choose these HICTOP clamps for 6mm GT2 loops; choose a belt kit with buckles included if you are also replacing the belt.
Before you order
Checks for HICTOP GT2 belt clamps.
Check before you buy
- Your printer uses 6mm GT2 belts
- The belt ends are joined by a crimp
- You have pliers to close them
- You can tension the belt afterwards
The product at a glance
HICTOP GT2 Belt Clamp Copper
Best for: Ender and CR-10 belt repairs
- Primary Material
- copper
View on Amazon: HICTOP GT2 Belt Clamp Copper Affiliate link
HICTOP GT2 belt clamps: 10 copper crimps for 6mm timing belts, closed with pliers, for Ender 3, Ender 5 and CR-10 style printers.
Pros
- Spares for many belt jobs
- Simple pliers fit
- Copper holds firmly
Cons
- 6mm belts only
- No dimensions listed
Good fit if
- You are replacing a 6mm GT2 belt
- You lost a buckle
Skip if
- Your printer uses 10mm belts
Verdict: Useful cheap spares for any Creality-style belt repair.
Specifications side by side
| Spec | HICTOP GT2 Belt Clamp Copper |
|---|---|
| Primary Material | copper |
| Size | GT2 Belt Clamps |
Frequently asked questions
What belt width do HICTOP GT2 clamps fit?
6mm GT2 timing belts.
How many clamps come in the HICTOP pack?
10 pieces.
What are the HICTOP belt clamps made of?
Copper.
Do I need a special tool for HICTOP GT2 clamps?
No, pliers are enough to crimp them.
Which printers use HICTOP's GT2 belt clamps?
HICTOP names the Ender 3, Ender 5 and CR-10.
See also
- bambu lab ams 4 slot review
- bambu lab liquid glue build plate review
- aladrs photon mono 4k screen protector review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- ideaformer 3d conveyor belt 3d printer review
- unxuey 50pcs 3d printer heatsink review
