ELEGOO Mercury Plus V3.0 Wash and Cure Station Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The ELEGOO Mercury Plus V3.0 is a two-in-one wash and cure station with a 7.5L tank, and it earns its place for owners of 10-inch class resin printers: the washing size is 9.05 x 5.31 x 10.24 inches, so a Saturn-size plate's worth of parts fits. ELEGOO says the tank holds 2.1 times as much as V2.0 and the curing area is 5.6 times larger. Curing uses a 360° turntable with 24 UV LEDs at 405nm around it, plus one LED under the clear turntable so the underside of a part cures too. A touch panel sets wash and cure times up to 30 minutes, an upgraded POM bearing keeps the wash rotation smooth, and the anti-UV cover blocks 99.9% of UV, with a micro switch that stops curing when you lift it. ELEGOO lists it for most LCD, DLP and SLA printers. It is a sizeable unit at 13.9 pounds shipped. All of this is from ELEGOO's own listing; we did not run the station.
What stands out
- 7.5L wash tank, 9.05 x 5.31 x 10.24in
- 24 UV LEDs + 1 under the turntable
- Up to 30-minute timer
- Cover blocks 99.9% UV, stops on lift
Who it fits
Good fit for
Owners of 10-inch resin printers such as a Saturn who want one station that washes a full plate of parts and cures them evenly from all sides.
Who should skip it
Owners of only a 7-inch printer with small batches, who can use a smaller station, or anyone short of bench space.
Verdict: A large, well-specified wash and cure station for 10-inch printer owners.
Mercury Plus V3.0 specs explained
7.5L tank
2.1 times V2.0, per ELEGOO; fills with IPA or water for water-wash resin.
9.05 x 5.31 x 10.24in wash size
Big enough for a 10-inch printer's build plate of parts.
24 x 405nm LEDs + bottom LED
Even cure from the sides and from below.
Up to 30 minutes
Maximum wash or cure time on the touch panel.
99.9% UV blocking cover
Protects your eyes; a micro switch cuts curing when opened.
Why the bottom LED matters
Many cure stations light parts only from the side and top, so the face resting on the turntable stays tacky until you flip it. The Mercury Plus V3.0 adds a single LED beneath the transparent turntable, which ELEGOO says removes blind spots. Combined with the 360° rotation, this cuts down on manual turning during curing.
Washing and curing with the V3.0
Fill the tank with your cleaning liquid, hang or place the parts in the wash basket, and set a time on the touch panel. The POM bearing drives the agitation. After washing and drying, swap to the turntable, close the UV cover and set the cure time. Keep cure runs short at first; overcuring can make thin parts brittle.
Before buying the Mercury Plus V3.0
Checks.
Check before you buy
- Your parts fit 9.05 x 5.31 x 10.24in in the Mercury Plus V3.0
- You have bench room and 7.5L of cleaning liquid for the V3.0
- Your resin cures at 405nm in the Mercury Plus V3.0
The product at a glance
ELEGOO Mercury Plus V3.0 Wash and Cure Station
Best for: 10-inch printer post-processing
- Printing Technology
- DLP
- Dimensions
- 24 × 17 × 15 inches
- Weight
- 13.9 pounds
View on Amazon: ELEGOO Mercury Plus V3.0 Wash and Cure Station Affiliate link
ELEGOO Mercury Plus V3.0: 7.5L wash (9.05x5.31x10.24in), 24 + 1 UV LEDs at 405nm on a 360° turntable, 30-minute timer, 99.9% UV cover.
Pros
- Large 7.5L tank
- Bottom LED for full cure
- Safety switch on the cover
Cons
- 13.9 lb and bulky
- 30-minute maximum per cycle
- Overkill for small 7-inch batches
Good fit if
- You run a 10-inch resin printer
Skip if
- You print only small 7-inch batches instead of Mercury Plus V3.0 loads
Verdict: A roomy two-in-one station for 10-inch printers.
Specifications side by side
| Spec | ELEGOO Mercury Plus V3.0 Wash and Cure Station |
|---|---|
| Printing Technology | DLP |
| Dimensions | 24 × 17 × 15 inches |
| Weight | 13.9 pounds |
| Size | Medium-Mercury Plus V3.0 |
| Color | Mercury Plus V3.0 |
| Model | EL-3D-MPV3 |
Frequently asked questions
How big is the ELEGOO Mercury Plus V3.0 tank?
7.5L, with a washing size of 9.05 x 5.31 x 10.24 inches.
How many UV lights does the Mercury Plus V3.0 have?
24 LEDs at 405nm around the turntable plus one under the transparent turntable.
What is the longest cycle on the Mercury Plus V3.0?
Wash and cure times can be set up to 30 minutes.
Does the Mercury Plus V3.0 work with non-ELEGOO printers?
ELEGOO says it suits most LCD, DLP and SLA resin printers.
See also
- elegoo mercury xs wash cure bundle review
- elegoo mars 5 4k resin 3d printer review
- flashforge adventurer 5m hotend pei plate review
- elegoo centauri carbon 3d printer review
- elegoo 5pcs acf release liner review
- ELEGOO Saturn 3 12K Resin 3D Printer Review (2026): A Spec-Based Look
- ELEGOO Mars 4 Ultra 9K Review: Specs, Pros and Cons
- ELEGOO Mercury Plus 2.0 Wash and Cure Station Review: Who It Fits and Who Should Skip It
- creality ender 3 v3 plus review
- shelly plus 1pm review
