ARKA 3D Printing Super Glue Gel (1.76 oz) Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This is a cyanoacrylate (CA) gel sold for one job: gluing FDM prints. The listing comes from ARKA Biotechnologie, though the title itself carries no brand name, and the tube is model KPG3D50G, a 50g / 1.76 oz size (the title rounds it to 1.75 oz). The gel form is the point: it stays where you put it on a vertical seam or a split model instead of running down the part, and it fills small gaps where printed halves do not meet perfectly. ARKA names PLA, ABS, PETG, TPU, ASA and nylon, says the bond holds up to 110°C and in humidity, and fits a needle tip that is meant not to clog between uses. The tube is pitched as about five times a standard small CA bottle, aimed at print farms and anyone gluing often. There is no cure time, no shelf life after opening and no mention of an activator. This review is based on the product listing.
What stands out
- CA gel that stays put on vertical seams
- Names PLA, PETG, ABS, TPU, ASA and nylon
- Anti-clog needle tip
- 50g tube, rated to 110°C
Who it fits
Good fit for
Makers who split large models into parts, repair broken prints, or glue functional pieces and want more glue than a small hobby bottle.
Who should skip it
Anyone bonding PP or PE prints, which CA does not grip well, or who needs a set time on the label.
Verdict: A sensible large tube of gel CA for printed parts; check cure speed yourself since the listing gives none.
KPG3D50G gel, in plain terms
Gel CA, no-drip
Thick enough for seams on vertical faces and gap filling.
PLA, ABS, PETG, TPU, ASA, nylon
Covers the filaments most people print.
Up to 110°C, humidity resistant
Suits RC parts and items used outdoors, per the listing.
Anti-clog needle tip
Meant to keep the nozzle from sealing shut between uses.
1.76 oz / 50g tube
Large for CA; useful if you glue often.
Gel CA versus thin CA for prints
Thin CA wicks into tight joints fast but runs off sloped surfaces and soaks into infill. A gel like this one sits on the surface, so it suits butt joints on split models, pinned joints and seams where the halves leave a small gap. The tradeoff is a slower grab, which the listing does not quantify. Clear color means squeeze-out stays light on white or grey prints, though CA can leave a white haze on dark filament.
Using the ARKA gel on prints
Sand glossy faces lightly and wipe off dust so the gel has something to grip. Apply a thin bead to one side, press the parts and hold them; the listing gives no clamp time, so hold until the joint stops moving. Wipe the needle tip before capping to keep it clear. For flexible TPU joints test a scrap first, as hard CA can crack when the part bends.
Before ordering this CA gel
A short check for the ARKA 1.76 oz gel.
Check before you buy
- Your prints are PLA, PETG, ABS, ASA, TPU or nylon, not PP, for the ARKA gel
- You glue often enough to use a 50g ARKA tube before it ages
- You can live without a stated set time for the ARKA gel
The product at a glance
ARKA Biotechnologie Gel Super Glue
Best for: Gluing and repairing FDM prints
- Compatible Material
- PLA, PETG, ABS, TPU
- Dimensions
- 1.5 × 1.5 × 4.61 inches
- Weight
- 1.76 ounces
View on Amazon: ARKA Biotechnologie Gel Super Glue Affiliate link
ARKA's 50g CA gel for 3D prints: a no-drip formula for seams and gaps, with an anti-clog tip and a 110°C claim.
Pros
- Gel stays on vertical seams
- Large 1.76 oz tube
- Long filament list including nylon
Cons
- No set time stated
- Brand name missing from the title
- No activator or shelf-life info
Good fit if
- You assemble split models
- You repair functional prints
Skip if
- You bond PP or PE prints
Verdict: A big tube of gel CA aimed squarely at printed parts.
Specifications side by side
| Spec | ARKA Biotechnologie Gel Super Glue |
|---|---|
| Compatible Material | PLA, PETG, ABS, TPU |
| Dimensions | 1.5 × 1.5 × 4.61 inches |
| Weight | 1.76 ounces |
| Size | 1.76 Fl Oz |
| Color | Clear |
| Model | KPG3D50G |
Frequently asked questions
Does the ARKA super glue gel work on PETG?
Yes, PETG is on its list with PLA, ABS, TPU, ASA and nylon.
How much glue is in the ARKA 3D printing gel tube?
1.76 oz, which the model code puts at 50g; the title rounds it to 1.75 oz.
How heat resistant is the ARKA gel bond?
The listing claims up to 110°C.
How fast does the ARKA CA gel set?
The listing does not give a set or cure time.
See also
- nova3d water washable abs like tough resin review
- nova3d 16k tgm tough resin beige review
- nagy dental guide resin clear 500g review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- singer singer super bundle review
- best 3d printers with resume printing
