5Aplusreprap Ender 3 Hotend Kit Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
This replacement hotend, sold under the 5Aplusreprap name, is an assembled J-head for most classic Creality printers: the CR-10 family (CR-10, S4, S5, 10S, Mini), CR-20 and CR-20 Pro, Ender 2, Ender 3, 3 Pro, 3 V2 and Ender 5. Its main change from the stock part is an M3 stud NTC 100K thermistor that screws into the heater block, so it cannot shake loose the way a clamped bead can. The heater and thermistor wires both end in quick-release plugs, and titanium alloy screws hold the block, which the seller says passes less heat to the heat sink. The box also holds five 0.4mm brass nozzles, two spare aluminum blocks, three silicone socks and a wrench. One mismatch: the title says a 24V 40W heater, while the model code reads 24V50W. These details are from the seller's listing.
What stands out
- M3 stud NTC 100K thermistor
- Quick-release heater and sensor plugs
- Five nozzles, two blocks, three socks
Who it fits
Good fit for
Ender 3, Ender 5 or CR-10 owners with a damaged heater, loose thermistor or ruined block who want a complete assembled replacement plus spares.
Who should skip it
Owners of newer direct-drive Creality printers such as the Ender 3 V3 series, and anyone who wants an all-metal high-temperature hotend.
Verdict: A well-stocked, assembled hotend swap for classic Creality printers.
5Aplusreprap hotend kit specs
M3 stud thermistor
NTC 3950 100K, screws in.
24V heater
40W in the title, 50W in the model code.
Quick plugs
Heater and thermistor.
Titanium alloy screws
Hold the heater block.
5 × 0.4mm brass nozzles
Plus 2 blocks, 3 socks.
Ender 3 / 5, CR-10, CR-20
Listed fit.
Why the stud thermistor helps
Stock Creality thermistors are glass beads held under a small screw; a bump or a nozzle change can loosen them and send a false reading. A stud thermistor screws into its own threaded hole in the block, so the reading stays steady as the head moves. The seller warns to tighten it by hand, not with a tool, since the thread is small.
Swapping the hotend
Cut power, unplug the old heater and thermistor, mount the new assembly and plug in the quick connectors. The seller recommends releveling the bed afterwards so the new nozzle does not scrape it. Check the heater wattage your board expects before ordering, given the 40W/50W mismatch. Pick this kit for a full hotend swap with spares; pick a single nozzle if only the tip is clogged.
Before you order
Checks for the 5Aplusreprap Ender 3 hotend kit.
Check before you buy
- Your printer is on the listed Creality fit list
- Your board is 24V
- You can confirm the 40W or 50W heater
- You will relevel the bed after fitting
The product at a glance
SAPLUSREPRAP Ender 3 Hotend Upgrade
Best for: Older Ender 3 and CR-10 repairs
- Nozzle Diameter
- 0.4mm
- Dimensions
- 3.5 × 5.2 × 1.2 inches
- Weight
- 4.5 ounces
View on Amazon: SAPLUSREPRAP Ender 3 Hotend Upgrade Affiliate link
Assembled J-head hotend sold as 5Aplusreprap: M3 stud 100K thermistor, quick plugs, 24V heater, 5 nozzles, 2 blocks, 3 socks, wrench.
Pros
- Secure stud thermistor
- Plug-in wiring
- Lots of spares
Cons
- 40W vs 50W heater mismatch
- Not for V3-series printers
Good fit if
- Your stock hotend is damaged
- Your thermistor keeps loosening
Skip if
- You want an all-metal high-temp hotend
Verdict: A complete, spare-rich hotend for older Creality machines.
Specifications side by side
| Spec | SAPLUSREPRAP Ender 3 Hotend Upgrade |
|---|---|
| Nozzle Diameter | 0.4mm |
| Dimensions | 3.5 × 5.2 × 1.2 inches |
| Weight | 4.5 ounces |
| Size | 1.75mm Nozzle Diameter |
| Color | Red Set A |
| Model | HTK-24V50W-1set |
Frequently asked questions
Which printers does the 5Aplusreprap hotend fit?
CR-10 models, CR-20 and CR-20 Pro, Ender 2, Ender 3, 3 Pro, 3 V2 and Ender 5.
What thermistor comes in the 5Aplusreprap kit?
An M3 stud NTC 3950 100K thermistor.
How many nozzles come with the 5Aplusreprap hotend?
Five 0.4mm brass nozzles.
Is the 5Aplusreprap heater 40W or 50W?
The title says 40W but the model code says 50W; confirm before buying.
Should I relevel after fitting the 5Aplusreprap hotend?
Yes, the seller suggests it to keep the nozzle off the bed.
Featured in
See also
- imetrx dual gear extruder v3 review
- anycubic 4 in 1 filament hub kobra review
- anycubic mini purifier heater review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- creality ender 3 v3 se review
- yunzii b75 pro 75 wireless mechanical keyboard review
