iMetrx Dual Gear Extruder V3.0 Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Single-gear stock extruders on budget printers tend to slip, grind filament and wear out their plastic arms. iMetrx's V3.0 is a clear-bodied dual gear Bowden extruder (model US-BMGV3.0) aimed at that upgrade on the Ender 3, Ender 5 Pro, CR-10, Anycubic Mega S, Tevo Tornado, Wanhao D9, Anet A8 and E10, and Prusa i3-style DIY kits. The V3.0 changes are practical: an independent feeder guide inside the body to keep the filament path smooth, a pneumatic push fitting in place of the old Bowden buckle so that part alone can be replaced when it wears, and an angled body that clears the Z rod on printers where it sits close to the extruder, such as early Ender 3 units. The listing gives no gear ratio or E-step value, and a user manual is the only extra in the box. All of this is from iMetrx's listing.
What stands out
- Dual gear drive, clear body
- Replaceable pneumatic fitting
- Angled to clear a close Z rod
Who it fits
Good fit for
Owners of Ender 3, CR-10, Mega S or Anet-style Bowden printers whose stock extruder slips, cracks or grinds filament.
Who should skip it
Owners of direct drive printers, and anyone who wants a stated gear ratio and E-step value before buying.
Verdict: A practical dual gear swap for older Bowden printers; calibrate E-steps yourself.
iMetrx V3.0 extruder specs
Dual gear drive
Grips filament from both sides.
Internal feeder guide
Smoother filament path.
Pneumatic fitting
Replace the fitting alone.
Angled for Z rod
Fits close-rod frames.
Clear body, 4.6 oz
Model US-BMGV3.0.
Gear ratio
Not stated.
What the V3.0 changes fix
Push fittings wear: the teeth that grip the PTFE tube loosen, the tube creeps and retraction gets sloppy. Making the fitting a separate pneumatic connector means you replace a small part instead of the extruder. The inner guide keeps soft filament from wandering between the gears and the outlet. The angled body is a fit fix, not a performance one, for frames where the Z rod blocks a straight extruder.
Fitting and calibration
Mount it in place of the stock extruder, reuse the motor and connect the Bowden tube to the new fitting. Because the listing gives no gear ratio or steps value, measure and set E-steps after installing: mark the filament, extrude a fixed length, measure what actually went through and adjust. Choose the iMetrx if a clear body and a replaceable fitting matter to you; choose a model with a published ratio if you want to set E-steps from a number.
Before you order
Checks for the iMetrx dual gear V3.0 extruder.
Check before you buy
- Your printer is a Bowden setup on iMetrx's list
- You can calibrate E-steps yourself
- Your Z rod sits close to the extruder, or not
- You keep a spare PTFE tube on hand
The product at a glance
iMetrx Dual Gear Extruder V3.0
Best for: Older Bowden printers
- Weight
- 4.6 ounces
View on Amazon: iMetrx Dual Gear Extruder V3.0 Affiliate link
iMetrx V3.0 clear dual gear Bowden extruder: inner filament guide, replaceable pneumatic fitting, angled body for close Z rods; no gear ratio listed.
Pros
- Dual gear grip
- Cheap fitting replacement
- Clears close Z rods
Cons
- No ratio or E-step value
- Bowden setups only
Good fit if
- Your stock extruder slips or cracks
- Your Z rod blocks a straight extruder
Skip if
- Your printer is direct drive
Verdict: A solid low-cost extruder fix for older Bowden machines.
Specifications side by side
| Spec | iMetrx Dual Gear Extruder V3.0 |
|---|---|
| Weight | 4.6 ounces |
| Size | BMG |
| Color | Clean |
| Model | US-BMGV3.0 |
Frequently asked questions
Does the iMetrx V3.0 extruder fit the Ender 3?
Yes, along with the Ender 5 Pro, CR-10, Mega S, Tevo Tornado, Wanhao D9, Anet A8 and E10.
What gear ratio does the iMetrx V3.0 use?
iMetrx gives no ratio on the V3.0 page.
Can I replace the push fitting on the iMetrx extruder?
Yes, the V3.0 uses a pneumatic connector that can be swapped alone.
Why is the iMetrx V3.0 extruder angled?
To clear the Z rod on printers where it sits close, such as early Ender 3 units.
What comes in the iMetrx extruder box?
The extruder set and a user manual.
See also
- anycubic 4 in 1 filament hub kobra review
- anycubic mini purifier heater review
- anycubic photon mono 4 LCD review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- lexar lexar jumpdrive dual drive review
- redroad robotic pool cleaner dual drive review
