YOOPAI 1.75mm Red PETG Filament Review: Who It Fits and Who Should Skip It
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
At $15.98 for 1kg, this red YOOPAI PETG is one of the cheaper kilo rolls in the catalogue. It is 1.75mm with a ±0.03mm tolerance, a bit looser than the ±0.02mm many rolls quote, and the seller suggests 220-250°C at the nozzle with a 70-80°C bed. The pitch is a tough, glossy material that sits between PLA and ABS, with low odour and a claim of less stringing. The listing calls it suitable for most 1.75mm FDM machines and singles out Creality printers. A black version of the same roll has its own review on this site. Our notes rest only on the seller's page.
What stands out
- Low price per kilo
- Print settings stated plainly
- Glossy, light-transmitting red
- Dried and vacuum-packed before shipping
Who it fits
Good fit for
Anyone printing brackets, planters, enclosures or outdoor-ish household parts who wants PETG's toughness at a budget price and already has a heated bed reaching 70°C.
Who should skip it
Skip it if you need ±0.02mm consistency for fine detail, or if your printer cannot hold a 70°C bed.
Verdict: A cheap, clearly specified red PETG for practical parts.
Reading the red PETG specs
1kg, 1.75mm ±0.03mm
Standard roll size; tolerance is acceptable for everyday parts but not the tightest available.
Nozzle 220-250°C, bed 70-80°C
Typical PETG window; a printer that only reaches 60°C on the bed may struggle with adhesion.
Clarity and gloss
Light passes through thin walls, which suits lamp shades and display pieces.
Vacuum-sealed, pre-dried
Less moisture at first use, so fewer bubbles and pops in the nozzle.
Material and spool
YOOPAI describes a fully machine-wound spool meant to avoid snapping and tangles, sealed after drying to keep dust and moisture off. PETG itself bends before it breaks, which is why it suits clips and mounts better than plain PLA. Odour is described as minimal. The listing does not give spool dimensions, so if you use an automatic feeder, confirm the fit on arrival.
Day-to-day printing
Start near the middle of the stated ranges, around 235°C and 75°C, then tune. PETG often strings when it is wet or too hot, so dry the roll if it has been open for a while. A glue stick or textured plate helps release on smooth PEI, where PETG can bond too firmly. The red tint makes layer lines show on flat faces; curved shapes hide them better.
Worth confirming
A few points decide whether this roll fits your setup.
Check before you buy
- Bed reaches at least 70°C
- ±0.03mm tolerance is fine for your parts
- You have a way to dry PETG if it absorbs moisture
- Red, semi-clear gloss is the look you want
The product at a glance
YOOPAI 1.75mm Red PETG Filament 1kg
Best for: Budget red PETG for functional parts
- Material Type
- PETG
- Filament Diameter
- 1.75 mm
- Net Weight
- 1 kg
- Dimensional Accuracy
- +/- 0.03 mm
- Surface Finish
- Glossy
- Color
- Red
View on Amazon: YOOPAI 1.75mm Red PETG Filament 1kg Affiliate link
YOOPAI red PETG, 1kg of 1.75mm filament at ±0.03mm, with suggested settings of 220-250°C nozzle and 70-80°C bed, pre-dried and vacuum-sealed, $15.98.
Pros
- Budget price for a full kilo
- Clear temperature guidance
- Glossy red that transmits light
Cons
- Looser ±0.03mm tolerance
- Needs a 70°C-capable bed
- No spool size given
Good fit if
- You print tough red mounts or planters
- You want PETG on a tight budget
Skip if
- Your bed tops out below 70°C
- You chase ±0.02mm consistency
Verdict: Solid value for practical red PETG parts.
Specifications side by side
| Spec | YOOPAI 1.75mm Red PETG Filament 1kg |
|---|---|
| Material Type | PETG |
| Filament Diameter | 1.75 mm |
| Net Weight | 1 kg |
| Dimensional Accuracy | +/- 0.03 mm |
| Surface Finish | Glossy |
| Compatible Material | PETG |
| Color | Red |
| Weight | 2.2 pounds |
| Size | 1.75mm 1kg |
| Model | P-PETG-Red |
Frequently asked questions
What temperatures does YOOPAI recommend for this PETG?
A 220-250°C nozzle and a 70-80°C build plate.
Will it run on non-Creality printers?
The listing says it works with most 1.75mm FDM printers and mentions Creality as an especially good match.
How does the black roll compare?
It appears to be the same PETG in another colour, with the same tolerance and settings in its listing.
Is the red see-through?
The seller describes good clarity and light transmission, so thin walls will glow when lit.
Featured in
See also
- yoopai petg filament 1 75mm review
- yoopai vented resin printer enclosure review
- entina tina2c mini 3d printer review
- yoopai sunlu rainbow pla filament review
- yoopai sunlu silk pla filament review
- Creality CR-PETG 4kg Pack (Black/White/Red/Blue) Review
- creality k2 se 3d printer review
- easycargo 30pcs 3d printer heatsink review
