Hemulac Bambu Lab P2S Stainless Steel Extruder Gear Kit Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
Hemulac's kit replaces the gear set inside the Bambu Lab P2S extruder, the part that grips filament and pushes it to the hotend. It comes as a set rather than a single gear: a stainless steel drive gear, the driven pulley, a bearing, a spring, three washers and an M3x8 screw. Worn or clogged gear teeth show up as clicking, ground-down filament, gaps in extrusion and failed prints, and the listing pitches the kit as the fix for those symptoms. Stainless steel resists wear and corrosion, which matters if you run CF-filled or other abrasive filament. One line on the page compares it with plastic parts, though extruder drive gears on the P2S are already metal, so treat that claim as marketing. Hemulac gives no tooth count, gear ratio, hardness figure or install steps, and lists only the P2S. The yellow color in the size field likely refers to the pulley or packaging. This review leans on Hemulac's listing and published specs, not on a fitted kit.
What stands out
- Bambu Lab P2S extruder gear set
- Stainless drive gear and driven pulley
- Bearing, spring, 3 washers, M3x8 screw
- Fixes slipping or grinding feed
- No gear specs or install steps
Who it fits
Good fit for
P2S owners whose extruder clicks, grinds filament or under-extrudes after heavy use or abrasive filament, and who are comfortable opening the extruder.
Who should skip it
P1S, X1 or A1 owners (different extruders), and anyone whose feed problem is a clogged nozzle rather than worn gears.
Verdict: A complete small-parts set for P2S gear wear, with little technical detail.
Hemulac P2S gear kit contents
Stainless drive gear
Grips the filament; wear-resistant steel.
Driven pulley
The second gear in the pair.
Bearing and spring
Set the idler pressure on the filament.
3 washers, M3x8 screw
Small hardware so nothing is missing mid-repair.
P2S only
No other Bambu model is listed.
Why the P2S gear set comes complete
Replacing only the drive gear can leave a worn pulley or a tired spring in place, and the feed problem comes back. Having the bearing, spring, washers and screw in the same bag means the whole gear path is renewed at once. Keep the old parts until the first test print succeeds.
Diagnosing a P2S feed problem first
Before opening the extruder, rule out a clog: cold-pull or clean the nozzle and check that filament moves freely from the spool. If the extruder still clicks and the filament shows chewed bite marks, worn gear teeth or a weak spring are likely, and this set targets both. Follow Bambu's P2S extruder maintenance guide, since Hemulac gives no steps.
Before buying the Hemulac P2S gear set
Checks.
Check before you buy
- Your printer is a Bambu Lab P2S
- The P2S nozzle is clear and the extruder still slips
- You can open the P2S extruder using Bambu's guide
The product at a glance
Hemulac Stainless Steel Extruder Gear for Bambu Lab P2S
Best for: P2S extruder repair
- Primary Material
- Stainless Steel
- Color
- Yellow
View on Amazon: Hemulac Stainless Steel Extruder Gear for Bambu Lab P2S Affiliate link
Hemulac stainless steel extruder gear set for the Bambu P2S: drive gear, driven pulley, bearing, spring, washers and screw; no gear specs or guide.
Pros
- Full gear path in one bag
- Stainless steel for wear
- Targets slipping and grinding
Cons
- P2S only
- No tooth count or ratio
- Marketing compares with plastic parts
Good fit if
- Your P2S extruder grinds filament
Skip if
- Your feed issue is a nozzle clog
Verdict: A full gear-path refresh for the P2S.
Specifications side by side
| Spec | Hemulac Stainless Steel Extruder Gear for Bambu Lab P2S |
|---|---|
| Primary Material | Stainless Steel |
| Color | Yellow |
| Size | P2S Stainless Steel Extruder Gear Assembly |
Frequently asked questions
Does the Hemulac stainless gear kit fit the Bambu P1S?
The listing names the P2S only.
What parts are in the Hemulac P2S gear assembly?
A stainless drive gear and its driven pulley, plus a bearing, a spring, 3 washers and one M3x8 screw.
Is the Hemulac P2S drive gear hardened?
Hemulac says stainless steel but gives no hardness figure.
Does the Hemulac P2S gear set include install steps?
No, use Bambu's P2S extruder guide.
Featured in
See also
- elegoo 8k standard resin space grey 2kg review
- sunlu fast curing standard resin grey 3kg review
- heygears paf10 white resin 1kg review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- vocvoi stainless steel pans review
- feekaa stainless steel humidifier review
