GBSCLOVER 3-Piece X/Y/Z Timing Belt Kit Review (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
GBSCLOVER's set is three pre-cut belts for an X, Y and Z axis printer, packed in a storage box, and it is one of the few sets that gives every dimension: 31.50, 30.71 and 25.59 inches long, 2mm pitch, with the middle belt 8mm wide and the other two 6mm. The belts are fiberglass with a rubber coating, which GBSCLOVER says softens contact with the pulleys and reduces noise. Each has a buckle pressed on one end. The page never names a printer, only 'X Y Z axes 3D printers'. The lengths match the Kobra 3 belt sets other sellers list (X 31.5, Y 30.7, Z 25.59 inches), so this is very likely a Kobra 3 set. The 8mm Y belt is a detail those listings do not give, so measure your Y belt width before buying. The storage box keeps spares from kinking, a small but real plus. All figures are GBSCLOVER's.
What stands out
- Lengths 31.50 / 30.71 / 25.59 in
- Widths 6, 8, 6mm, 2mm pitch
- Storage box included
Who it fits
Good fit for
Owners whose X, Y and Z belts match these lengths, most likely Kobra 3 owners, who want stated widths.
Who should skip it
Anyone who needs a printer name on the box or a different belt length.
Verdict: Well-dimensioned belts with no printer named.
GBSCLOVER belt specs
31.50 in
X belt.
30.71 in, 8mm wide
Y belt.
25.59 in
Z belt.
2mm pitch, 6mm
X and Z width.
Fiberglass + rubber
Low-noise coating.
Storage box
Keeps spares flat.
Matching the set to a printer
Lay your old belts out and compare length and width, especially the 8mm Y belt. Many printers use 6mm on every axis; a printer that uses 8mm on Y needs exactly this split. If your figures match, the pre-pressed buckle on each belt makes the fit quicker than cutting from a roll.
Fitting and storing
Fit Y first while the bed is easy to reach, then X and Z, and re-tension each. Keep the box for spares, since folded belts can crack their fiberglass cords. Choose the GBSCLOVER set if you want widths and a box; choose FKBAightccy's Kobra 3 kit if you want the printer named and ten spare buckles.
Before you order
Checks for the GBSCLOVER belt set.
Check before you buy
- Your belts measure 31.50, 30.71 and 25.59 in
- Your Y belt is 8mm wide like GBSCLOVER's
- Your printer uses 2mm pitch
- You want a storage box
The product at a glance
GBSCLOVER 3Pcs 3D Printer Belt Kit
Best for: Kobra 3-size belts
- Primary Material
- Fiberglass, rubber
View on Amazon: GBSCLOVER 3Pcs 3D Printer Belt Kit Affiliate link
GBSCLOVER 3-belt set, 31.50/30.71/25.59 in, 6/8/6mm wide, 2mm pitch, fiberglass, storage box.
Pros
- Full dimensions
- 8mm Y belt stated
- Storage box
Cons
- No printer named
- No spare buckles listed
Good fit if
- Your belts match the sizes
- You want a box
Skip if
- You need a named fit
Verdict: Good if your measurements match.
Specifications side by side
| Spec | GBSCLOVER 3Pcs 3D Printer Belt Kit |
|---|---|
| Primary Material | Fiberglass, rubber |
Frequently asked questions
How long are the GBSCLOVER belts?
31.50, 30.71 and 25.59 inches.
What widths are the GBSCLOVER belts?
6mm, 8mm and 6mm, with a 2mm pitch.
Which printer does GBSCLOVER name?
None; the lengths match Kobra 3 sets from other sellers.
What are the GBSCLOVER belts made of?
Fiberglass with a rubber coating.
Do the GBSCLOVER belts include buckles?
Yes, one end of every GBSCLOVER belt carries a pressed buckle.
See also
- tyjan3d 61 piece bambu a1 tool kit review
- tyjan3d bambu p1 x1 maintenance tool kit review
- sigfee 3d printer enclosure ventilation review
- best 3d printers under 200
- best 3d printers under 300
- Best 3D Printers Under $500 in 2026: 7 Picks Ranked by Specs
- Best 3D Printers Under $1000: 6 Spec-Based Picks
- 6 Best 3D Printers Under $1500, Compared
- tkid 3d printer kids review
- easycargo 30pcs 3d printer heatsink review
