ELEGOO Mercury X Wash and Cure Station Review: Workflow and Limits (2026)
As an Amazon Associate we earn from qualifying purchases. Links on this page are affiliate links.
The Mercury X Bundle is a pair of post-processing machines for resin prints: a wash unit and a separate cure unit, so one batch can cure while the next washes. This listing is the most practical of ELEGOO's pages for the set. The wash bucket holds 7.5 liters, enough to wash parts from Saturn and Mars printers still attached to the build plate: you hang the plate inside and a stirring impeller moves solvent around the part. The cure unit uses two light bars with 14 LEDs each plus 4 LEDs under the turntable, all at 405nm and spread by a Fresnel lens, and a cover that blocks 99.9% of UV. Both run from a single knob: hold to switch on, turn to set the time. The listing is also frank about limits: the wash bucket must be filled before running or the impeller can jam, parts should be dried before curing, and water-washable resin is better rinsed under running water than washed in this machine. The account here follows ELEGOO's listing.
What stands out
- Wash and cure units run at the same time
- 7.5L bucket fits Saturn and Mars plates
- 405nm: 2 × 14 LED bars plus 4 under the turntable
- Cover blocks 99.9% of UV
Who it fits
Good fit for
Saturn and Mars owners using IPA-washed resins who want to clean prints on the plate and keep wash and cure going in parallel.
Who should skip it
Users of water-washable resin, and owners of printers with build plates larger than Saturn-class.
Verdict: A solid two-unit station for alcohol-washed resins on mid-size printers; skip it if you print water-washable.
Mercury X bundle, in plain terms
Two separate units
Wash one batch while the last one cures.
7.5L wash bucket, plate hanger
Clean Saturn and Mars prints without removing them first.
32 LEDs at 405nm, Fresnel lens
Even curing from the sides and below.
UV cover, 99.9% blocked
Safe to watch while it cures.
Single-knob control
Hold to power on, turn to set time.
How the workflow runs
Print, lift the plate off the printer and hang it in the wash bucket; the impeller stirs solvent around the part. Remove the part, let it dry, then place it on the cure unit's turntable under the cover. With two machines, the next plate can go into the wash while the first part cures. Another ELEGOO listing of the same set gives the tank as 7000ml, close to this page's 7.5L figure.
Rules the listing sets
Fill the bucket before every run, as an empty bucket can jam the wheel. Dry parts fully before curing, or the trapped solvent clouds the surface. Rinse water-washable resin parts under running water instead of in this tank. Keep the bucket lid on between sessions to slow solvent evaporation.
Before ordering the Mercury X set
A short check for ELEGOO's two-unit station.
Check before you buy
- Your resin printer plate is Saturn or Mars sized for the Mercury X bucket
- You wash in IPA or a similar solvent, not water, in the Mercury X
- You have bench space for two Mercury X units side by side
The product at a glance
ELEGOO Mercury X Dual Wash and Cure Station
Best for: Saturn and Mars owners using IPA
- Printing Technology
- Resin
- Dimensions
- 19 × 12 × 13 inches
View on Amazon: ELEGOO Mercury X Dual Wash and Cure Station Affiliate link
ELEGOO Mercury X Bundle: separate wash and cure units, a 7.5L bucket that takes Saturn and Mars plates, and 405nm Fresnel curing.
Pros
- Wash and cure in parallel
- Washes parts on the plate
- UV-blocking cover
Cons
- Not for water-washable resin
- Bucket must be filled before running
- Takes two units' worth of space
Good fit if
- You own a Saturn or Mars printer
Skip if
- You print water-washable resin
Verdict: A practical two-unit station for solvent-washed resins.
Specifications side by side
| Spec | ELEGOO Mercury X Dual Wash and Cure Station |
|---|---|
| Printing Technology | Resin |
| Dimensions | 19 × 12 × 13 inches |
| Size | Medium-Mercury X Bundle |
| Color | Mercury X Bundle |
| Model | Mercury X Bundle |
Frequently asked questions
Can the ELEGOO Mercury X wash water-washable resin?
ELEGOO advises rinsing water-washable parts under running water rather than in this machine.
Can you wash prints on the build plate in the Mercury X?
Yes, the plate hangs inside the 7.5L bucket.
How many LEDs does the Mercury X cure unit have?
Two light bars with 14 LEDs each plus 4 under the turntable.
Can the Mercury X wash and cure at the same time?
Yes, the two units are separate and work in parallel.
See also
- flashforge ad5m nozzle sizes materials review
- flashforge adventurer 5m family first printer review
- flashforge ad5m hs pla sample bundle review
- elegoo centauri carbon 3d printer review
- elegoo 5pcs acf release liner review
- ELEGOO Saturn 3 12K Resin 3D Printer Review (2026): A Spec-Based Look
- ELEGOO Mars 4 Ultra 9K Review: Specs, Pros and Cons
- ELEGOO Mercury Plus 2.0 Wash and Cure Station Review: Who It Fits and Who Should Skip It
- rancilio silvia pro x dual review
- sanodesk dual motor 63 x 28 review
